BFD for OSPFv3 configuration example
Network requirements
As shown in Figure 110:
Configure OSPFv3 on Switch A, Switch B and Switch C and configure BFD over the link Switch A<—>L2 Switch<—>Switch B.
After the link Switch A<—>L2 Switch<—>Switch B fails, BFD can quickly detect the failure and notify OSPFv3 of the failure. Then Switch A and Switch B communicate through Switch C.
Figure 110: Network diagram
Table 26: Interface and IP address assignment
Device | Interface | IPv6 address |
---|---|---|
Switch A | Vlan-int10 | 2001::1/64 |
Switch A | Vlan-int11 | 2001:2::1/64 |
Switch B | Vlan-int10 | 2001::2/64 |
Switch B | Vlan-int13 | 2001:3::2/64 |
Switch C | Vlan-int11 | 2001:2::2/64 |
Switch C | Vlan-int13 | 2001:3::1/64 |
Configuration procedure
Configure IPv6 addresses for the interfaces. (Details not shown.)
Configure basic OSPFv3:
# On Switch A, enable OSPFv3 and specify the router ID as 1.1.1.1.
<SwitchA> system-view [SwitchA] ospfv3 [SwitchA-ospfv3-1] router-id 1.1.1.1 [SwitchA-ospfv3-1] quit [SwitchA] interface vlan-interface 10 [SwitchA-Vlan-interface10] ospfv3 1 area 0 [SwitchA-Vlan-interface10] quit [SwitchA] interface vlan-interface 11 [SwitchA-Vlan-interface11] ospfv3 1 area 0 [SwitchA-Vlan-interface11] quit
# On Switch B, enable OSPFv3 and specify the router ID as 2.2.2.2.
<SwitchB> system-view [SwitchB] ospfv3 [SwitchB-ospfv3-1] router-id 2.2.2.2 [SwitchB-ospfv3-1] quit [SwitchB] interface vlan-interface 10 [SwitchB-Vlan-interface10] ospfv3 1 area 0 [SwitchB-Vlan-interface10] quit [SwitchB] interface vlan-interface 13 [SwitchB-Vlan-interface13] ospfv3 1 area 0 [SwitchB-Vlan-interface13] quit
# On Switch C, enable OSPFv3 and specify the router ID as 3.3.3.3.
<SwitchC> system-view [SwitchC] ospfv3 [SwitchC-ospfv3-1] router-id 3.3.3.3 [SwitchC-ospfv3-1] quit [SwitchC] interface vlan-interface 11 [SwitchC-Vlan-interface11] ospfv3 1 area 0 [SwitchC-Vlan-interface11] quit [SwitchC] interface vlan-interface 13 [SwitchC-Vlan-interface13] ospfv3 1 area 0 [SwitchC-Vlan-interface13] quit
Configure BFD:
# Enable BFD and configure BFD parameters on Switch A.
[SwitchA] bfd session init-mode active [SwitchA] interface vlan-interface 10 [SwitchA-Vlan-interface10] ospfv3 bfd enable [SwitchA-Vlan-interface10] bfd min-transmit-interval 500 [SwitchA-Vlan-interface10] bfd min-receive-interval 500 [SwitchA-Vlan-interface10] bfd detect-multiplier 7 [SwitchA-Vlan-interface10] return
# Enable BFD and configure BFD parameters on Switch B.
[SwitchB] bfd session init-mode active [SwitchB] interface vlan-interface 10 [SwitchB-Vlan-interface10] ospfv3 bfd enable [SwitchB-Vlan-interface10] bfd min-transmit-interval 500 [SwitchB-Vlan-interface10] bfd min-receive-interval 500 [SwitchB-Vlan-interface10] bfd detect-multiplier 6
Verifying the configuration
# Display the BFD information on Switch A.
<SwitchA> display bfd session Total Session Num: 1 Init Mode: Active IPv6 Session Working Under Ctrl Mode: Local Discr: 1441 Remote Discr: 1450 Source IP: FE80::20F:FF:FE00:1202 (link-local address of VLAN-interface 10 on Switch A) Destination IP: FE80::20F:FF:FE00:1200 (link-local address of VLAN-interface 10 on Switch B) Session State: Up Interface: Vlan10 Hold Time: 2319ms
# Display routes destined for 2001:4::0/64 on Switch A.
<SwitchA> display ipv6 routing-table 2001:4::0 64 Summary Count : 1 Destination: 2001:4::/64 Protocol : O_INTRA NextHop : FE80::20F:FF:FE00:1200 Preference: 10 Interface : Vlan10 Cost : 1
The output information shows that Switch A communicates with Switch B through VLAN-interface 10. The link over VLAN-interface 10 fails.
# Display routes to 2001:4::0/64 on Switch A.
<SwitchA> display ipv6 routing-table 2001:4::0 64 Summary Count : 1 Destination: 2001:4::/64 Protocol : O_INTRA NextHop : FE80::BAAF:67FF:FE27:DCD0 Preference: 10 Interface : Vlan11 Cost : 2
The output shows that Switch A communicates with Switch B through VLAN-interface 11.