Dual-homed rings configuration example
Network requirements
As shown in Figure 22:
Device A through Device H form RRPP domain 1. Specify the primary control VLAN of RRPP domain 1 as VLAN 4092. Specify the protected VLANs of RRPP domain 1 as VLANs 1 through 30.
Device A through Device D form primary ring 1. Device A, Device B, and Device E form subring 2. Device A, Device B, and Device F form subring 3. Device C, Device D, and Device G form subring 4. Device C, Device D, and Device H form subring 5.
Specify Device A, Device E, Device F, Device G, and Device H as the master nodes of Ring 1, Ring 2, Ring 3, Ring 4, and Ring 5, respectively. Specify GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port on the rings.
Specify Device A as the edge node of the connected subrings, its GigabitEthernet 1/0/3 and GigabitEthernet 1/0/4 as the edge ports. Specify Device D as the transit node of the primary ring and edge node of the connected subrings, its GigabitEthernet 1/0/3 and GigabitEthernet 1/0/4 as the edge ports. Specify Device B and Device C as the transit node of the primary ring and assistant edge nodes of the connected subrings, their GigabitEthernet 1/0/3 and GigabitEthernet 1/0/4 as the edge ports.
![[IMPORTANT: ]](images/important.png) | IMPORTANT: Configure the primary and secondary ports on the master nodes correctly to make sure other protocols still operate correctly when protected VLANs are denied by the secondary ports. | |
Figure 22: Network diagram
Configuration procedure
Configure Device A:
# Create VLANs 1 through 30.
<DeviceA> system-view [DeviceA] vlan 1 to 30
# Map these VLANs to MSTI 1.
[DeviceA] stp region-configuration [DeviceA-mst-region] instance 1 vlan 1 to 30
# Activate the MST region configuration.
[DeviceA-mst-region] active region-configuration [DeviceA-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 1/0/1.
[DeviceA] interface gigabitethernet 1/0/1 [DeviceA-GigabitEthernet1/0/1] link-delay 0
# Disable the spanning tree feature on the port.
[DeviceA-GigabitEthernet1/0/1] undo stp enable
# Configure the port as a trunk port.
[DeviceA-GigabitEthernet1/0/1] port link-type trunk
# Assign the port to VLANs 1 through 30.
[DeviceA-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceA-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceA] interface gigabitethernet 1/0/2 [DeviceA-GigabitEthernet1/0/2] link-delay 0 [DeviceA-GigabitEthernet1/0/2] undo stp enable [DeviceA-GigabitEthernet1/0/2] port link-type trunk [DeviceA-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 [DeviceA-GigabitEthernet1/0/2] quit
# Configure GigabitEthernet 1/0/3 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceA] interface gigabitethernet 1/0/3 [DeviceA-GigabitEthernet1/0/3] link-delay 0 [DeviceA-GigabitEthernet1/0/3] undo stp enable [DeviceA-GigabitEthernet1/0/3] port link-type trunk [DeviceA-GigabitEthernet1/0/3] port trunk permit vlan 1 to 30 [DeviceA-GigabitEthernet1/0/3] quit
# Configure GigabitEthernet 1/0/4 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceA] interface gigabitethernet 1/0/4 [DeviceA-GigabitEthernet1/0/4] link-delay 0 [DeviceA-GigabitEthernet1/0/4] undo stp enable [DeviceA-GigabitEthernet1/0/4] port link-type trunk [DeviceA-GigabitEthernet1/0/4] port trunk permit vlan 1 to 30 [DeviceA-GigabitEthernet1/0/4] quit
# Create RRPP domain 1.
[DeviceA] rrpp domain 1
# Configure VLAN 4092 as the primary control VLAN of RRPP domain 1.
[DeviceA-rrpp-domain1] control-vlan 4092
# Configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[DeviceA-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device A as the master node of primary ring 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port. Enable ring 1.
[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceA-rrpp-domain1] ring 1 enable
# Configure Device A as the edge node of subring 2, with GigabitEthernet 1/0/4 as the edge port. Enable subring 2.
[DeviceA-rrpp-domain1] ring 2 node-mode edge edge-port gigabitethernet 1/0/4 [DeviceA-rrpp-domain1] ring 2 enable
# Configure Device A as the edge node of subring 3, with GigabitEthernet 1/0/3 as the edge port. Enable subring 3.
[DeviceA-rrpp-domain1] ring 3 node-mode edge edge-port gigabitethernet 1/0/3 [DeviceA-rrpp-domain1] ring 3 enable [DeviceA-rrpp-domain1] quit
# Enable RRPP.
[DeviceA] rrpp enable
Configure Device B:
# Create VLANs 1 through 30.
<DeviceB> system-view [DeviceB] vlan 1 to 30
# Map these VLANs to MSTI 1.
[DeviceB] stp region-configuration [DeviceB-mst-region] instance 1 vlan 1 to 30
# Activate the MST region configuration.
[DeviceB-mst-region] active region-configuration [DeviceB-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 1/0/1.
[DeviceB] interface gigabitethernet 1/0/1 [DeviceB-GigabitEthernet1/0/1] link-delay 0
# Disable the spanning tree feature on the port.
[DeviceB-GigabitEthernet1/0/1] undo stp enable
# Configure the port as a trunk port.
[DeviceB-GigabitEthernet1/0/1] port link-type trunk
# Assign the port to VLANs 1 through 30.
[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceB-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceB] interface gigabitethernet 1/0/2 [DeviceB-GigabitEthernet1/0/2] link-delay 0 [DeviceB-GigabitEthernet1/0/2] undo stp enable [DeviceB-GigabitEthernet1/0/2] port link-type trunk [DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 [DeviceB-GigabitEthernet1/0/2] quit
# Configure GigabitEthernet 1/0/3 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceB] interface gigabitethernet 1/0/3 [DeviceB-GigabitEthernet1/0/3] link-delay 0 [DeviceB-GigabitEthernet1/0/3] undo stp enable [DeviceB-GigabitEthernet1/0/3] port link-type trunk [DeviceB-GigabitEthernet1/0/3] port trunk permit vlan 1 to 30 [DeviceB-GigabitEthernet1/0/3] quit
# Configure GigabitEthernet 1/0/4 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceB] interface gigabitethernet 1/0/4 [DeviceB-GigabitEthernet1/0/4] link-delay 0 [DeviceB-GigabitEthernet1/0/4] undo stp enable [DeviceB-GigabitEthernet1/0/4] port link-type trunk [DeviceB-GigabitEthernet1/0/4] port trunk permit vlan 1 to 30 [DeviceB-GigabitEthernet1/0/4] quit
# Create RRPP domain 1.
[DeviceB] rrpp domain 1
# Configure VLAN 4092 as the primary control VLAN of RRPP domain 1.
[DeviceB-rrpp-domain1] control-vlan 4092
# Configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[DeviceB-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device B as the transit node of primary ring 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port. Enable ring 1.
[DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceB-rrpp-domain1] ring 1 enable
# Configure Device B as the assistant edge node of subring 2, with GigabitEthernet 1/0/4 as the edge port. Enable subring 2.
[DeviceB-rrpp-domain1] ring 2 node-mode assistant-edge edge-port gigabitethernet 1/0/4 [DeviceB-rrpp-domain1] ring 2 enable
# Configure Device B as the assistant edge node of subring 3, with GigabitEthernet 1/0/3 as the edge port. Enable subring 3.
[DeviceB-rrpp-domain1] ring 3 node-mode assistant-edge edge-port gigabitethernet 1/0/3 [DeviceB-rrpp-domain1] ring 3 enable [DeviceB-rrpp-domain1] quit
# Enable RRPP.
[DeviceB] rrpp enable
Configure Device C:
# Create VLANs 1 through 30.
<DeviceC> system-view [DeviceC] vlan 1 to 30
# Map these VLANs to MSTI 1.
[DeviceC] stp region-configuration [DeviceC-mst-region] instance 1 vlan 1 to 30
# Activate the MST region configuration.
[DeviceC-mst-region] active region-configuration [DeviceC-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 1/0/1.
[DeviceC] interface gigabitethernet 1/0/1 [DeviceC-GigabitEthernet1/0/1] link-delay 0
# Disable the spanning tree feature on the port.
[DeviceC-GigabitEthernet1/0/1] undo stp enable
# Configure the port as a trunk port.
[DeviceC-GigabitEthernet1/0/1] port link-type trunk
# Assign the port to VLANs 1 through 30.
[DeviceC-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceC-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceC] interface gigabitethernet 1/0/2 [DeviceC-GigabitEthernet1/0/2] link-delay 0 [DeviceC-GigabitEthernet1/0/2] undo stp enable [DeviceC-GigabitEthernet1/0/2] port link-type trunk [DeviceC-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 [DeviceC-GigabitEthernet1/0/2] quit
# Configure GigabitEthernet 1/0/3 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceC] interface gigabitethernet 1/0/3 [DeviceC-GigabitEthernet1/0/3] link-delay 0 [DeviceC-GigabitEthernet1/0/3] undo stp enable [DeviceC-GigabitEthernet1/0/3] port link-type trunk [DeviceC-GigabitEthernet1/0/3] port trunk permit vlan 1 to 30 [DeviceC-GigabitEthernet1/0/3] quit
# Configure GigabitEthernet 1/0/4 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceC] interface gigabitethernet 1/0/4 [DeviceC-GigabitEthernet1/0/4] link-delay 0 [DeviceC-GigabitEthernet1/0/4] undo stp enable [DeviceC-GigabitEthernet1/0/4] port link-type trunk [DeviceC-GigabitEthernet1/0/4] port trunk permit vlan 1 to 30 [DeviceC-GigabitEthernet1/0/4] quit
# Create RRPP domain 1.
[DeviceC] rrpp domain 1
# Configure VLAN 4092 as the primary control VLAN of RRPP domain 1.
[DeviceC-rrpp-domain1] control-vlan 4092
# Configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[DeviceC-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device C as the transit node of primary ring 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port. Enable ring 1.
[DeviceC-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceC-rrpp-domain1] ring 1 enable
# Configure Device C as the assistant edge node of subring 4, with GigabitEthernet 1/0/3 as the edge port. Enable subring 4.
[DeviceC-rrpp-domain1] ring 4 node-mode assistant-edge edge-port gigabitethernet 1/0/3 [DeviceC-rrpp-domain1] ring 4 enable
# Configure Device C as the assistant edge node of subring 5, with GigabitEthernet 1/0/4 as the edge port. Enable subring 5.
[DeviceC-rrpp-domain1] ring 5 node-mode assistant-edge edge-port gigabitethernet 1/0/4 [DeviceC-rrpp-domain1] ring 5 enable [DeviceC-rrpp-domain1] quit
# Enable RRPP.
[DeviceC] rrpp enable
Configure Device D:
# Create VLANs 1 through 30.
<DeviceD> system-view [DeviceD] vlan 1 to 30
# Map these VLANs to MSTI 1.
[DeviceD] stp region-configuration [DeviceD-mst-region] instance 1 vlan 1 to 30
# Activate the MST region configuration.
[DeviceD-mst-region] active region-configuration [DeviceD-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 1/0/1.
[DeviceD] interface gigabitethernet 1/0/1 [DeviceD-GigabitEthernet1/0/1] link-delay 0
# Disable the spanning tree feature on the port.
[DeviceD-GigabitEthernet1/0/1] undo stp enable
# Configure the port as a trunk port.
[DeviceD-GigabitEthernet1/0/1] port link-type trunk
# Assign the port to VLANs 1 through 30.
[DeviceD-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceD-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceD] interface gigabitethernet 1/0/2 [DeviceD-GigabitEthernet1/0/2] link-delay 0 [DeviceD-GigabitEthernet1/0/2] undo stp enable [DeviceD-GigabitEthernet1/0/2] port link-type trunk [DeviceD-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 [DeviceD-GigabitEthernet1/0/2] quit
# Configure GigabitEthernet 1/0/3 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceD] interface gigabitethernet 1/0/3 [DeviceD-GigabitEthernet1/0/3] link-delay 0 [DeviceD-GigabitEthernet1/0/3] undo stp enable [DeviceD-GigabitEthernet1/0/3] port link-type trunk [DeviceD-GigabitEthernet1/0/3] port trunk permit vlan 1 to 30 [DeviceD-GigabitEthernet1/0/3] quit
# Configure GigabitEthernet 1/0/4 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceD] interface gigabitethernet 1/0/4 [DeviceD-GigabitEthernet1/0/4] link-delay 0 [DeviceD-GigabitEthernet1/0/4] undo stp enable [DeviceD-GigabitEthernet1/0/4] port link-type trunk [DeviceD-GigabitEthernet1/0/4] port trunk permit vlan 1 to 30 [DeviceD-GigabitEthernet1/0/4] quit
# Create RRPP domain 1.
[DeviceD] rrpp domain 1
# Configure VLAN 4092 as the primary control VLAN of RRPP domain 1.
[DeviceD-rrpp-domain1] control-vlan 4092
# Configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[DeviceD-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device D as the transit node of primary ring 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port. Enable ring 1.
[DeviceD-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceD-rrpp-domain1] ring 1 enable
# Configure Device D as the edge node of subring 4, with GigabitEthernet 1/0/3 as the edge port. Enable subring 4.
[DeviceD-rrpp-domain1] ring 4 node-mode edge edge-port gigabitethernet 1/0/3 [DeviceD-rrpp-domain1] ring 4 enable
# Configure Device D as the edge node of subring 5, with GigabitEthernet 1/0/4 as the edge port. Enable subring 5.
[DeviceD-rrpp-domain1] ring 5 node-mode edge edge-port gigabitethernet 1/0/4 [DeviceD-rrpp-domain1] ring 5 enable [DeviceD-rrpp-domain1] quit
# Enable RRPP.
[DeviceD] rrpp enable
Configure Device E:
# Create VLANs 1 through 30.
<DeviceE> system-view [DeviceE] vlan 1 to 30
# Map these VLANs to MSTI 1.
[DeviceE] stp region-configuration [DeviceE-mst-region] instance 1 vlan 1 to 30
# Activate the MST region configuration.
[DeviceE-mst-region] active region-configuration [DeviceE-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 1/0/1.
[DeviceE] interface gigabitethernet 1/0/1 [DeviceE-GigabitEthernet1/0/1] link-delay 0
# Disable the spanning tree feature on the port.
[DeviceE-GigabitEthernet1/0/1] undo stp enable
# Configure the port as a trunk port.
[DeviceE-GigabitEthernet1/0/1] port link-type trunk
# Assign the port to VLANs 1 through 30.
[DeviceE-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceE-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceE] interface gigabitethernet 1/0/2 [DeviceE-GigabitEthernet1/0/2] link-delay 0 [DeviceE-GigabitEthernet1/0/2] undo stp enable [DeviceE-GigabitEthernet1/0/2] port link-type trunk [DeviceE-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 [DeviceE-GigabitEthernet1/0/2] quit
# Create RRPP domain 1.
[DeviceE] rrpp domain 1
# Configure VLAN 4092 as the primary control VLAN of RRPP domain 1.
[DeviceE-rrpp-domain1] control-vlan 4092
# Configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[DeviceE-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device E as the master node of subring 2, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port. Enable subring 2.
[DeviceE-rrpp-domain1] ring 2 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 1 [DeviceE-rrpp-domain1] ring 2 enable [DeviceE-rrpp-domain1] quit
# Enable RRPP.
[DeviceE] rrpp enable
Configure Device F:
# Create VLANs 1 through 30.
<DeviceF> system-view [DeviceF] vlan 1 to 30
# Map these VLANs to MSTI 1.
[DeviceF] stp region-configuration [DeviceF-mst-region] instance 1 vlan 1 to 30
# Activate the MST region configuration.
[DeviceF-mst-region] active region-configuration [DeviceF-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 1/0/1.
[DeviceF] interface gigabitethernet 1/0/1 [DeviceF-GigabitEthernet1/0/1] link-delay 0
# Disable the spanning tree feature on the port.
[DeviceF-GigabitEthernet1/0/1] undo stp enable
# Configure the port as a trunk port.
[DeviceF-GigabitEthernet1/0/1] port link-type trunk
# Assign the port to VLANs 1 through 30.
[DeviceF-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceF-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceF] interface gigabitethernet 1/0/2 [DeviceF-GigabitEthernet1/0/2] link-delay 0 [DeviceF-GigabitEthernet1/0/2] undo stp enable [DeviceF-GigabitEthernet1/0/2] port link-type trunk [DeviceF-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 [DeviceF-GigabitEthernet1/0/2] quit
# Create RRPP domain 1.
[DeviceF] rrpp domain 1
# Configure VLAN 4092 as the primary control VLAN of RRPP domain 1.
[DeviceF-rrpp-domain1] control-vlan 4092
# Configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[DeviceF-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device F as the master node of subring 3, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port. Enable subring 3.
[DeviceF-rrpp-domain1] ring 3 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 1 [DeviceF-rrpp-domain1] ring 3 enable [DeviceF-rrpp-domain1] quit
# Enable RRPP.
[DeviceF] rrpp enable
Configure Device G:
# Create VLANs 1 through 30.
<DeviceG> system-view [DeviceG] vlan 1 to 30
# Map these VLANs to MSTI 1.
[DeviceG] stp region-configuration [DeviceG-mst-region] instance 1 vlan 1 to 30
# Activate the MST region configuration.
[DeviceG-mst-region] active region-configuration [DeviceG-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 1/0/1.
[DeviceG] interface gigabitethernet 1/0/1 [DeviceG-GigabitEthernet1/0/1] link-delay 0
# Disable the spanning tree feature on the port.
[DeviceG-GigabitEthernet1/0/1] undo stp enable
# Configure the port as a trunk port.
[DeviceG-GigabitEthernet1/0/1] port link-type trunk
# Assign the port to VLANs 1 through 30.
[DeviceG-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceG-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceG] interface gigabitethernet 1/0/2 [DeviceG-GigabitEthernet1/0/2] link-delay 0 [DeviceG-GigabitEthernet1/0/2] undo stp enable [DeviceG-GigabitEthernet1/0/2] port link-type trunk [DeviceG-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 [DeviceG-GigabitEthernet1/0/2] quit
# Create RRPP domain 1.
[DeviceG] rrpp domain 1
# Configure VLAN 4092 as the primary control VLAN of RRPP domain 1.
[DeviceG-rrpp-domain1] control-vlan 4092
# Configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[DeviceG-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device G as the master node of subring 4, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port. Enable subring 4.
[DeviceG-rrpp-domain1] ring 4 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 1 [DeviceG-rrpp-domain1] ring 4 enable [DeviceG-rrpp-domain1] quit
# Enable RRPP.
[DeviceG] rrpp enable
Configure Device H:
# Create VLANs 1 through 30.
<DeviceH> system-view [DeviceH] vlan 1 to 30
# Map these VLANs to MSTI 1.
[DeviceH] stp region-configuration [DeviceH-mst-region] instance 1 vlan 1 to 30
# Activate the MST region configuration.
[DeviceH-mst-region] active region-configuration [DeviceH-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 1/0/1.
[DeviceH] interface gigabitethernet 1/0/1 [DeviceH-GigabitEthernet1/0/1] link-delay 0
# Disable the spanning tree feature on the port.
[DeviceH-GigabitEthernet1/0/1] undo stp enable
# Configure the port as a trunk port.
[DeviceH-GigabitEthernet1/0/1] port link-type trunk
# Assign the port to VLANs 1 through 30.
[DeviceH-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceH-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2 in the same way GigabitEthernet 1/0/1 is configured.
[DeviceH] interface gigabitethernet 1/0/2 [DeviceH-GigabitEthernet1/0/2] link-delay 0 [DeviceH-GigabitEthernet1/0/2] undo stp enable [DeviceH-GigabitEthernet1/0/2] port link-type trunk [DeviceH-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 [DeviceH-GigabitEthernet1/0/2] quit
# Create RRPP domain 1.
[DeviceH] rrpp domain 1
# Configure VLAN 4092 as the primary control VLAN of RRPP domain 1.
[DeviceH-rrpp-domain1] control-vlan 4092
# Configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[DeviceH-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device H as the master node of subring 5, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port. Enable subring 5.
[DeviceH-rrpp-domain1] ring 5 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 1 [DeviceH-rrpp-domain1] ring 5 enable [DeviceH-rrpp-domain1] quit
# Enable RRPP.
[DeviceH] rrpp enable
Verifying the configuration
# Use the display commands to view RRPP configuration and operational information on each device.