Layer 2 dynamic aggregation configuration example

Network requirements

On the network shown in Figure 13, perform the following tasks:

Figure 13: Network diagram

Configuration procedure

  1. Configure Device A:

    # Create VLAN 10, and assign the port Ten-GigabitEthernet 1/0/4 to VLAN 10.

    <DeviceA> system-view
    [DeviceA] vlan 10
    [DeviceA-vlan10] port ten-gigabitethernet 1/0/4
    [DeviceA-vlan10] quit
    

    # Create VLAN 20, and assign the port Ten-GigabitEthernet 1/0/5 to VLAN 20.

    [DeviceA] vlan 20
    [DeviceA-vlan20] port ten-gigabitethernet 1/0/5
    [DeviceA-vlan20] quit
    

    # Create Layer 2 aggregate interface Bridge-Aggregation 1, and set the link aggregation mode to dynamic.

    [DeviceA] interface bridge-aggregation 1
    [DeviceA-Bridge-Aggregation1] link-aggregation mode dynamic
    [DeviceA-Bridge-Aggregation1] quit
    

    # Assign ports Ten-GigabitEthernet 1/0/1 through Ten-GigabitEthernet 1/0/3 to link aggregation group 1.

    [DeviceA] interface ten-gigabitethernet 1/0/1
    [DeviceA-Ten-GigabitEthernet1/0/1] port link-aggregation group 1
    [DeviceA-Ten-GigabitEthernet1/0/1] quit
    [DeviceA] interface ten-gigabitethernet 1/0/2
    [DeviceA-Ten-GigabitEthernet1/0/2] port link-aggregation group 1
    [DeviceA-Ten-GigabitEthernet1/0/2] quit
    [DeviceA] interface ten-gigabitethernet 1/0/3
    [DeviceA-Ten-GigabitEthernet1/0/3] port link-aggregation group 1
    [DeviceA-Ten-GigabitEthernet1/0/3] quit
    

    # Configure Layer 2 aggregate interface Bridge-Aggregation 1 as a trunk port and assign it to VLANs 10 and 20.

    [DeviceA] interface bridge-aggregation 1
    [DeviceA-Bridge-Aggregation1] port link-type trunk
    [DeviceA-Bridge-Aggregation1] port trunk permit vlan 10 20
    [DeviceA-Bridge-Aggregation1] quit
    
  2. Configure Device B in the same way Device A is configured. (Details not shown.)

Verifying the configuration

# Display detailed information about all aggregation groups on Device A.

[DeviceA] display link-aggregation verbose
Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing
Port Status: S -- Selected, U -- Unselected
             I -- Individual, * -- Management port
Flags:  A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,
        D -- Synchronization, E -- Collecting, F -- Distributing,
        G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation1
Aggregation Mode: Dynamic
Loadsharing Type: Shar
Management VLAN : None
System ID: 0x8000, 000f-e267-6c6a
Local:
  Port               Status  Priority Oper-Key  Flag
--------------------------------------------------------------------------------
  XGE1/0/1           S       32768    1         {ACDEF}
  XGE1/0/2           S       32768    1         {ACDEF}
  XGE1/0/3           S       32768    1         {ACDEF}
Remote:
  Actor            Partner Priority Oper-Key  SystemID               Flag
--------------------------------------------------------------------------------
  XGE1/0/1           1       32768    1         0x8000, 000f-e267-57ad {ACDEF}
  XGE1/0/2           2       32768    1         0x8000, 000f-e267-57ad {ACDEF}
  XGE1/0/3           3       32768    1         0x8000, 000f-e267-57ad {ACDEF}

The output shows that: