Printable version

Drivers & software

** CRITICAL ** HPE MSA 1040/2040/1050/2050 and P2000 G3 300GB, 450GB and 600GB 12G SAS 15K rpm SFF Drive Models (EH0300JDYTH, EH0450JDYTK and EH0600JDYTL) Hard Drive Firmware

By downloading, you agree to the terms and conditions of the Hewlett Packard Enterprise Software License Agreement.
Note:  Some software requires a valid warranty, current Hewlett Packard Enterprise support contract, or a license fee.

Type: Firmware - SAS Storage Disk
Version: HPD6(13 Mar 2018)
Operating System(s): HP-UX 11.23
HP-UX 11.31 (IA)
Microsoft Windows Server 2012
Microsoft Windows Server 2012 R2
Microsoft Windows Server 2016
Red Hat Enterprise Linux 6 Server (x86)
Red Hat Enterprise Linux 6 Server (x86-64)
Red Hat Enterprise Linux 7 Server
SUSE Linux Enterprise Server 11 (AMD64/EM64T)
SUSE Linux Enterprise Server 11 (x86)
SUSE Linux Enterprise Server 12
VMware ESXi 5.0
VMware vSphere 5.1
VMware vSphere 5.5
VMware vSphere 6.0
VMware vSphere 6.5
Multi-part download
File name: HP_EH0300JDYTH_HPD6.fla (1.9 MB)
File name: HP_EH0450JDYTK_HPD6.fla (1.9 MB)
File name: HP_EH0600JDYTL_HPD6.fla (1.9 MB)
The firmware available in this download is specifically packaged for flashing the SFF hard drive models EH0300JDYTH (300GB 12G SAS 15K), EH0450JDYTK (450GB 12G SAS 15K) and EH0600JDYTL (600GB 12G SAS 15K) when configured in HPE MSA 1040/2040/1050/2050 and P2000 G3 Storage Arrays.

Prerequisites:

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE:

  • Drives of the same model in the storage system must have the same firmware revision.
  • To install this firmware, you must download the firmware package from the HPE website and save the file to your local filesystem.

To ensure the integrity of your download, HPE recommends verifying your results with the following SHA-256 Checksum values:

596076e8ea263b5d72da0394fddfcfe2eff2d162059b1b9a5e16aeb25448e7bd HP_EH0600JDYTL_HPD6.fla
9907c86325e02af5d880089f3eae457176bb734c584d29d9f1c7b50e38ad4bff HP_EH0450JDYTK_HPD6.fla
6ea285d00788cfb7fbbc140a961e160198015dc1a89611a42a2b48b53ac6f4ad HP_EH0300JDYTH_HPD6.fla

Reboot Requirement:
Reboot is not required after installation for updates to take effect and hardware stability to be maintained.


Installation:

Installation instructions using Storage Management Utility (SMU):

  1. Place the downloaded firmware file in a temporary directory.
  2. Stop I/O to controller before starting the firmware update.
  3. Login to the SMU. For SMU v3 (MSA 1040, MSA 2040, MSA 1050 and MSA 2050) go to System > Actions > Update Firmware > Update Disk Drives or for SMU v2 (P2000 G3, MSA 1040 and MSA 2040) select Tools > Update Firmware . A table displays currently installed firmware versions.
  4. Select the drives to update. Click Browse and select the firmware file to install.
  5. Click OK button, or if using SMU v2 click Install Disk Firmware File.
  6. Wait for progress messages to specify that the update is complete.
  7. In the SMU display, verify that the proper firmware version appears for each disk drive.

Installation instructions using FTP or SFTP:

Using the SMU, prepare to use FTP or SFTP:

  • Determine the network-port IP addresses of the system controllers.
  • Verify that the system FTP or SFTP service is enabled.
  • Verify that the user has permission to use the FTP interface and manage access rights.

Obtain address of the disks:

  • Obtain the address of each disk to be loaded in the form (for example, 0:1 and 1:9) and obtain the firmware revision of each of these disks.
  • Determine which disks need to be updated based on the revision.
    Note: In SMU v3, System->Front and put cursor on disk,Tool tip shows the location of the disk.  In SMU v2, the disk addresses are displayed by clicking on each enclosure in the Configuration View, present in the left pane and then selecting the desired disk. The needed data is displayed in the fields labeled 'Enclosure ID', 'Slot' and 'Revision'.
    Note: In the CLI, enter 'show disks'. The required information is displayed in the columns labeled 'Location' and 'Revision'.

Obtain SFTP port number :

  • In CLI, to know the SFTP port number, execute “show protocols” command.
  • In SMU , go to Home->Action-> Configuration Wizard-> Enable system-management services  and check the SFTP port number.

Instructions for updating disk firmware using FTP or SFTP:

  1. Stop all I/O to controller before starting the firmware update.
  2. Place the downloaded firmware file in a temporary directory.
  3. Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory containing the firmware file to load.
  4. To flash using ftp, enter ftp <ip address>. (For example: ftp 10.1.0.9) for Windows and Linux OS.
  5. To flash using sftp, enter sftp -P <sftp port number>  <user>@<controller-network-address>. (For example: sftp -P 1022 ftp@10.1.0.9) for Linux OS. A 3rd party SFTP client application is required to flash via SFTP from Windows, eg. CURL executable.
  6. Login via FTP or SFTP with username and password having manage access role
  7. To update a specific drive, type "put FILENAME disk:ENCLOSURE-ID:SLOT-NUMBER" where FILENAME is the name of new firmware image to load, ENCLOSURE-ID is the enclosure number and SLOT-NUMBER is the slot number of the drive in the enclosure.
  8. It typically takes several minutes for the firmware update progress to complete. Messages will be displayed in the FTP interface during this time. WARNING! Do not power cycle or restart during the firmware update as this can result in loss of capabilities for this unit.
  9. Repeat steps 6-7 for each disk to update in each enclosure.
  10. Quit the FTP or SFTP session.
  11. Using SMU or CLI verify that the proper firmware version appears for each disk drive.

NOTE:

  • Only HPE MSA 1050 and 2050 storage arrays have support for SFTP. 

End User License Agreements:
HPE Software License Agreement v1


Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


Important:

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE:

  • Drives of the same model in the storage system must have the same firmware revision.
  • To install this firmware, you must download the firmware package from the HPE website and save the file to your local filesystem.

Supported Devices and Features:

Firmware on the listed drives can be updated when attached to any of the following Storage Systems:

  • HPE P2000 G3 10GbE iSCSI MSA Dual Controller SFF Array System      
  • HPE P2000 G3 iSCSI MSA Dual Controller SFF Array System      
  • HPE P2000 G3 SAS MSA Dual Controller SFF Array System      
  • HPE P2000 G3 MSA FC Dual Controller SFF Modular Smart Array System     
  • HPE P2000 G3 MSA FC/iSCSI Dual Combo Controller SFF Array
  • HPE MSA 1040 SAN SFF Storage
  • HPE MSA 1040 SAS SFF Storage
  • HPE MSA 2040 SAN SFF Storage
  • HPE MSA 2040 SAS SFF Storage
  • HPE MSA 2042 SAN SFF Storage
  • HPE MSA 2042 SAS SFF Storage
  • HPE MSA 1050 SAN SFF Storage
  • HPE MSA 1050 SAS SFF Storage 
  • HPE MSA 2050 SAN SFF Storage
  • HPE MSA 2050 SAS SFF Storage
  • HPE MSA 2052 SAN SFF Storage
  • HPE MSA 2052 SAS SFF Storage
  • HPE MSA 2050 SFF Disk Enclosure

Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


Following fixes were added to this version of firmware

  • Data integrity risk where a recoverable error can prevent a write command from completing properly.
  • Data integrity risk due to incorrect re-ordering of commands, when overlapped commands occur. 
  • Data integrity risk during very large blocks of sequential commands with a data transfer between 1020MB and 1024MB.
  • Data integrity risk during a sequential read and write workload when a recovered error is encountered, which could cause incomplete data to be read. 

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE:

  • Drives of the same model in the storage system must have the same firmware revision.
  • To install this firmware, you must download the firmware package from the HPE website and save the file to your local filesystem.
Version:HPD6 (13 Mar 2018)
Fixes

Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


Following fixes were added to this version of firmware

  • Data integrity risk where a recoverable error can prevent a write command from completing properly.
  • Data integrity risk due to incorrect re-ordering of commands, when overlapped commands occur. 
  • Data integrity risk during very large blocks of sequential commands with a data transfer between 1020MB and 1024MB.
  • Data integrity risk during a sequential read and write workload when a recovered error is encountered, which could cause incomplete data to be read. 

Version:HPD4 (4 Nov 2015)
Fixes

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.


Following issue is fixed in this firmware:

  • This firmware fixes a self-initiated reset issue during ATI (Adjacent Track Interference) mitigation. Servo improvements were also added that correct miscalculations and calibrate the drive for better performance. The firmware download time required has increased due to these included servo improvements (not fast download compliant).

Type: Firmware - SAS Storage Disk
Version: HPD6(13 Mar 2018)
Operating System(s):
HP-UX 11.23
HP-UX 11.31 (IA)
Microsoft Windows Server 2012
Microsoft Windows Server 2012 R2
Microsoft Windows Server 2016
Red Hat Enterprise Linux 6 Server (x86)
Red Hat Enterprise Linux 6 Server (x86-64)
Red Hat Enterprise Linux 7 Server
SUSE Linux Enterprise Server 11 (AMD64/EM64T)
SUSE Linux Enterprise Server 11 (x86)
SUSE Linux Enterprise Server 12
VMware ESXi 5.0
VMware vSphere 5.1
VMware vSphere 5.5
VMware vSphere 6.0
VMware vSphere 6.5

Description

The firmware available in this download is specifically packaged for flashing the SFF hard drive models EH0300JDYTH (300GB 12G SAS 15K), EH0450JDYTK (450GB 12G SAS 15K) and EH0600JDYTL (600GB 12G SAS 15K) when configured in HPE MSA 1040/2040/1050/2050 and P2000 G3 Storage Arrays.

Installation Instructions

Prerequisites:

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE:

  • Drives of the same model in the storage system must have the same firmware revision.
  • To install this firmware, you must download the firmware package from the HPE website and save the file to your local filesystem.

To ensure the integrity of your download, HPE recommends verifying your results with the following SHA-256 Checksum values:

596076e8ea263b5d72da0394fddfcfe2eff2d162059b1b9a5e16aeb25448e7bd HP_EH0600JDYTL_HPD6.fla
9907c86325e02af5d880089f3eae457176bb734c584d29d9f1c7b50e38ad4bff HP_EH0450JDYTK_HPD6.fla
6ea285d00788cfb7fbbc140a961e160198015dc1a89611a42a2b48b53ac6f4ad HP_EH0300JDYTH_HPD6.fla

Reboot Requirement:
Reboot is not required after installation for updates to take effect and hardware stability to be maintained.


Installation:

Installation instructions using Storage Management Utility (SMU):

  1. Place the downloaded firmware file in a temporary directory.
  2. Stop I/O to controller before starting the firmware update.
  3. Login to the SMU. For SMU v3 (MSA 1040, MSA 2040, MSA 1050 and MSA 2050) go to System > Actions > Update Firmware > Update Disk Drives or for SMU v2 (P2000 G3, MSA 1040 and MSA 2040) select Tools > Update Firmware . A table displays currently installed firmware versions.
  4. Select the drives to update. Click Browse and select the firmware file to install.
  5. Click OK button, or if using SMU v2 click Install Disk Firmware File.
  6. Wait for progress messages to specify that the update is complete.
  7. In the SMU display, verify that the proper firmware version appears for each disk drive.

Installation instructions using FTP or SFTP:

Using the SMU, prepare to use FTP or SFTP:

  • Determine the network-port IP addresses of the system controllers.
  • Verify that the system FTP or SFTP service is enabled.
  • Verify that the user has permission to use the FTP interface and manage access rights.

Obtain address of the disks:

  • Obtain the address of each disk to be loaded in the form (for example, 0:1 and 1:9) and obtain the firmware revision of each of these disks.
  • Determine which disks need to be updated based on the revision.
    Note: In SMU v3, System->Front and put cursor on disk,Tool tip shows the location of the disk.  In SMU v2, the disk addresses are displayed by clicking on each enclosure in the Configuration View, present in the left pane and then selecting the desired disk. The needed data is displayed in the fields labeled 'Enclosure ID', 'Slot' and 'Revision'.
    Note: In the CLI, enter 'show disks'. The required information is displayed in the columns labeled 'Location' and 'Revision'.

Obtain SFTP port number :

  • In CLI, to know the SFTP port number, execute “show protocols” command.
  • In SMU , go to Home->Action-> Configuration Wizard-> Enable system-management services  and check the SFTP port number.

Instructions for updating disk firmware using FTP or SFTP:

  1. Stop all I/O to controller before starting the firmware update.
  2. Place the downloaded firmware file in a temporary directory.
  3. Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory containing the firmware file to load.
  4. To flash using ftp, enter ftp <ip address>. (For example: ftp 10.1.0.9) for Windows and Linux OS.
  5. To flash using sftp, enter sftp -P <sftp port number>  <user>@<controller-network-address>. (For example: sftp -P 1022 ftp@10.1.0.9) for Linux OS. A 3rd party SFTP client application is required to flash via SFTP from Windows, eg. CURL executable.
  6. Login via FTP or SFTP with username and password having manage access role
  7. To update a specific drive, type "put FILENAME disk:ENCLOSURE-ID:SLOT-NUMBER" where FILENAME is the name of new firmware image to load, ENCLOSURE-ID is the enclosure number and SLOT-NUMBER is the slot number of the drive in the enclosure.
  8. It typically takes several minutes for the firmware update progress to complete. Messages will be displayed in the FTP interface during this time. WARNING! Do not power cycle or restart during the firmware update as this can result in loss of capabilities for this unit.
  9. Repeat steps 6-7 for each disk to update in each enclosure.
  10. Quit the FTP or SFTP session.
  11. Using SMU or CLI verify that the proper firmware version appears for each disk drive.

NOTE:

  • Only HPE MSA 1050 and 2050 storage arrays have support for SFTP. 

Release Notes

End User License Agreements:
HPE Software License Agreement v1


Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


Important:

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE:

  • Drives of the same model in the storage system must have the same firmware revision.
  • To install this firmware, you must download the firmware package from the HPE website and save the file to your local filesystem.

Supported Devices and Features:

Firmware on the listed drives can be updated when attached to any of the following Storage Systems:

  • HPE P2000 G3 10GbE iSCSI MSA Dual Controller SFF Array System      
  • HPE P2000 G3 iSCSI MSA Dual Controller SFF Array System      
  • HPE P2000 G3 SAS MSA Dual Controller SFF Array System      
  • HPE P2000 G3 MSA FC Dual Controller SFF Modular Smart Array System     
  • HPE P2000 G3 MSA FC/iSCSI Dual Combo Controller SFF Array
  • HPE MSA 1040 SAN SFF Storage
  • HPE MSA 1040 SAS SFF Storage
  • HPE MSA 2040 SAN SFF Storage
  • HPE MSA 2040 SAS SFF Storage
  • HPE MSA 2042 SAN SFF Storage
  • HPE MSA 2042 SAS SFF Storage
  • HPE MSA 1050 SAN SFF Storage
  • HPE MSA 1050 SAS SFF Storage 
  • HPE MSA 2050 SAN SFF Storage
  • HPE MSA 2050 SAS SFF Storage
  • HPE MSA 2052 SAN SFF Storage
  • HPE MSA 2052 SAS SFF Storage
  • HPE MSA 2050 SFF Disk Enclosure

Fixes

Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


Following fixes were added to this version of firmware

  • Data integrity risk where a recoverable error can prevent a write command from completing properly.
  • Data integrity risk due to incorrect re-ordering of commands, when overlapped commands occur. 
  • Data integrity risk during very large blocks of sequential commands with a data transfer between 1020MB and 1024MB.
  • Data integrity risk during a sequential read and write workload when a recovered error is encountered, which could cause incomplete data to be read. 

Important

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE:

  • Drives of the same model in the storage system must have the same firmware revision.
  • To install this firmware, you must download the firmware package from the HPE website and save the file to your local filesystem.

Revision History

Version:HPD6 (13 Mar 2018)
Fixes

Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


Following fixes were added to this version of firmware

  • Data integrity risk where a recoverable error can prevent a write command from completing properly.
  • Data integrity risk due to incorrect re-ordering of commands, when overlapped commands occur. 
  • Data integrity risk during very large blocks of sequential commands with a data transfer between 1020MB and 1024MB.
  • Data integrity risk during a sequential read and write workload when a recovered error is encountered, which could cause incomplete data to be read. 

Version:HPD4 (4 Nov 2015)
Fixes

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.


Following issue is fixed in this firmware:

  • This firmware fixes a self-initiated reset issue during ATI (Adjacent Track Interference) mitigation. Servo improvements were also added that correct miscalculations and calibrate the drive for better performance. The firmware download time required has increased due to these included servo improvements (not fast download compliant).

Legal Disclaimer: Products sold prior to the November 1, 2015 separation of Hewlett-Packard Company into Hewlett Packard Enterprise Company and HP Inc. may have older product names and model numbers that differ from current models.