Show commands

If RIPng is not configured on the switch, any show commands related to RIPng are executed, the following output is displayed.

show ipv6 ripng
RIPng Configuration Information
RIPng protocol : Disabled

Show IPv6 ripng general

Syntax

show ipv6 ripng general

Description

Displays RIPng global parameters only as shown below.

RIPng global parameters

HP-3810M-24GT-1s(config)# show ipv6 ripng general
RIPng global parameters
RIPng protocol : Enabled
Default metric : 1
Administrative distance : 120
Route changes : 1090
Queries : 134457
Update time : 30
Timeout : 180
Garbage-collect time : 120
HP-3810M-24GT-1s(config)#

Show IPv6 ripng interface

Syntax

show ipv6 ripng interface

Description

Displays basic config, interface and peer information as shown below.

Options

VLAN	Specify the VLAN of the interface requesting detailed information.
VLAN-ID	Enter a VLAN identifier or a VLAN name.

Usage

show ipv6 ripng interface vlan VLAN-ID

RIPng interface information

HP-3810M-24GT-1s(config)# show ipv6 ripng
RIPng global parameters
RIPng protocol : Enabled
Default metric : 1
Administrative distance : 120
Route changes : 2090
Queries : 134877
Update time : 30
Timeout : 180
Garbage-collect time : 120

RIPng interface information
VLAN         Status       Metric
----------- ----------- -----------
10           Enabled         1
20           Enabled         1

RIPng peer information
                                                  Bad     Last update
IPv6 Address                                     packets   timeticks
---------------------------------------------- --------- ------------
fe80::200:eff:feda:98b6%vlan10                     0          27

Show IPv6 RIPng peer

Syntax

show ipv6 ripng peer

Description

Shows the peers learned through RIPng.

RIPng peer information

RIPng peer information
  IPv6 Address               Bad packets  Last update timeticks
  -------------------------- ----------- ---------------------
  fe80::ab23:ccff:fef4:fc40 0     30


	NOTE: Since RIPng does not have an active peering mechanism, this command shows only those RIPng peers from which a route was taken and added to the routing table. For example, if two peers advertise the same route(s) with the same metric only one of them will be shown as peer.

Show IPv6 RIPng redistribute

Syntax

show ipv6 ripng redistribute

Description

List the protocols that are being redistributed into RIPng.

RIPng redistributing without route-maps

RIPng redistributing
Route type Route map Options
---------- ---------------------------------- -----------------
Connected

RIPng redistribute with route-maps

RIPng redistributing
 Route type   Route map           Options
 ----------   ------------------- ---------------------------------------
Connected     map2                static map1 Include blackhole and reject

Show IPv6 RIPng traps

Syntax

show ipv6 ripng traps

Description

Display the enabled RIPng traps.

RIPng Traps : Enabled

RIPng Traps : Enabled
  RIPng Traps Enabled
  
  -------------------
  Interface State Change
  Interface Configuration Error
  Interface Bad Packet Receive Error

Show IPv6 route RIPng

Syntax

show ipv6 route ripng

Description

Show the IPv6 routing table. The output can be restricted to a specific destination or type of route.

Options

IPv6-ADDR

The destination IPv6 address for which to display the routes.

Usage

show ipv6 route IPv6-ADDR static | connected | ospfv3 | ripng

IPv6 route entries

IPv6 Route Entries

T (Type):
    S: Static
    O: OSPFv3
    C: Connected
    R:RIPng

ST (Sub-type):
    O : OSPF Intra
    E1: External1
    N1: NSSA Ext1
    OI: OSPF Inter
    E2: External2
    N2: NSSA Ext2

Destination/Gateway                    T  ST   Distance   Metric
------------------------------------- --- --- ---------- ----------
1::/64
    VLAN1 (DEFAULT_VLAN)               R   NA     120       1

Show ipv6 route summary

Syntax

show ipv6 route summary

Description

Show the summary of IPv6 routing table.

IPv6 route summary

IPv6 Route Table Summary
Protocol Active Routes
-------------- -------------
Connected 5
Ripng 4000

prev	up	next
VLAN Level Configuration	home	Debug commands