One-way PAP authentication configuration example

As shown in Figure 3, configure Router A to authenticate Router B by using PAP, but Router B not to authenticate Router A.

1. Configure Router A:

   # Create a user account for Router B.

   <RouterA> system-view
   [RouterA] local-user userb class network
   

   # Set a password for the user account.

   [RouterA-luser-network-userb] password simple passb
   

   # Set the service type of the user account to PPP.

   [RouterA-luser-network-userb] service-type ppp
   [RouterA-luser-network-userb] quit
   

   # Enable PPP encapsulation on Serial 2/1/0. By default, an interface uses PPP encapsulation.

   [RouterA] interface serial 2/1/0
   [RouterA-Serial2/1/0] link-protocol ppp
   

   # Set the authentication mode to PAP.

   [RouterA-Serial2/1/0] ppp authentication-mode pap domain system
   

   # Assign an IP address to Serial 2/1/0.

   [RouterA-Serial2/1/0] ip address 200.1.1.1 16
   [RouterA-Serial2/1/0] quit
   

   # Configure local authentication for the PPP users in the default ISP domain (system).

   [RouterA] domain system
   [RouterA-isp-system] authentication ppp local
   

2. Configure Router B:

   # Enable PPP encapsulation on Serial 2/1/0. By default, an interface uses PPP encapsulation.

   <RouterB> system-view
   [RouterB] interface serial 2/1/0
   [RouterB-Serial2/1/0] link-protocol ppp
   

   # Configure the PAP username and password sent from Router B to Router A when Router B is authenticated by Router A using PAP.

   [RouterB-Serial2/1/0] ppp pap local-user userb password simple passb
   

   # Assign an IP address to Serial 2/1/0 of Router B.

   [RouterB-Serial2/1/0] ip address 200.1.1.2 16
   

# Use the display interface serial command to display information about Serial 2/1/0 of Router B.

[RouterB-Serial2/1/0] display interface serial 2/1/0
Serial2/1/0
Current state: UP
Line protocol state: UP
Description: Serial2/1/0 Interface
Bandwidth: 64kbps
Maximum Transmit Unit: 1500
Internet Address: 200.1.1.2/16 Primary
Link layer protocol: PPP
LCP: opened, IPCP: opened
...

The output shows that:

• The physical layer status and link layer status of the interface are both up.

• The states of LCP and IPCP are both Opened, indicating that PPP negotiation has succeeded.

# Verify that Router A and Router B can ping each other.

[RouterB-Serial2/1/0] ping 200.1.1.1
5 packet(s) transmitted, 5 packet(s) received, 0.0% packet loss Ping 200.1.1.1 (200.1.1.1): 56 data bytes, press CTRL_C to break
56 bytes from 200.1.1.1: icmp_seq=0 ttl=128 time=3.197 ms
56 bytes from 200.1.1.1: icmp_seq=1 ttl=128 time=2.594 ms
56 bytes from 200.1.1.1: icmp_seq=2 ttl=128 time=2.739 ms
56 bytes from 200.1.1.1: icmp_seq=3 ttl=128 time=1.738 ms
56 bytes from 200.1.1.1: icmp_seq=4 ttl=128 time=1.744 ms

--- Ping statistics for 200.1.1.1 ---
5 packet(s) transmitted, 5 packet(s) received, 0.0% packet loss
round-trip min/avg/max/std-dev = 1.738/2.402/3.197/0.576 ms