Models, specifications, and compatibility
Product name (SKU) | Transmission distance | Data rate | Cable type | Connector type |
---|---|---|---|---|
HPE X121 1G SFP RJ45 T Transceiver (J8177C)
Aruba 1G SFP RJ45 T 100m Cat5e XCVR (J8177D) |
100 m (328.08 ft) | 1G
100Mbps1 |
Cat5e UTP/STP | RJ-45 |
For certain products. See next table.
Product name | SKU | Minimum software required (J8177C/J8177D) | Comments |
---|---|---|---|
1810 Series Switches | J9660A, J9801A, J9803A, J9834A | All | |
1820 Switch Series | J9980A, J9981A, J9983A, J9984A | All | |
1920S Switch Series | JL381A, JL382A, JL384A, JL385A, JL386A | All | The JL380A and JL383A switches do not include SFP ports. |
2510 Switch | J9020A | All | |
2530 Switch Series | J9782A, J9781A, J9776A, J9775A, J9779A, J9778A, J9773A, J9772A, J9856A, J9855A, J9854A, J9853A | All | |
2540 Switch Series | JL354A, JL355A, JL356A, JL357A | All | |
2610 Switch Series | J9085A, J9086A, J9087A, J9088A, J9089A | All | |
2620 Switch Series | J9623A, J9624A, J9625A, J9626A, J9627A | All | |
2920 Series Switches | J9731A | All | J8177C/J8177D is not supported for use in the Dual-Personality ports of the 2920 Series Switches. For use ONLY in the J9731A module. |
2930F Series Switches | JL253A, JL254A, JL255A, JL256A, JL258A, JL259A, JL260A, JL261A, JL262A, JL263A, JL264A, JL557A, JL558A, JL559A | All | J8177C/J8177D support both 100Mbps and 1G operation in this Switch Series. |
2930M Switch Series | JL083A | All | J8177C/J8177D are not supported for use in the Dual-Personality ports of the 2930M Series Switches.
For use in an installed JL083A Aruba 3810M/2930M 4SFP+ MACsec Module. J8177C/J8177D support both 100Mbps and 1G operation in this Switch Series. |
3800 Switch Series | J9573A, J9574A, J9575A, J9576A, J9584A | All | |
3810M Switch Series | JL075A, JL083A | All | For use in the SFP+ ports of the JL075A 3810M switch. Also used in any 3810M switch with a JL083A Aruba 3810M/2930M 4SFP+ MACsec Module installed.
J8177C/J8177D support both 100Mbps and 1G operation in this Switch Series. |
4100gl Switch Series | J4893A, J4908A | G.07.69 | |
4200vl Switch Series | J8776A, J9033A | All | |
5300xl Switch Series | J4878A/B | E.09.22 | |
5400zl Switch Series | J8705A, J8706A | All | |
J9308A | K.14.34 | ||
J9537A, J9549A, J9535A, J9637A | K.15.02.0004 | ||
5400R Switch Series | J9537A, J9549A, J9535A, J9637A | All | J8177C/J8177D support both 100Mbps and 1G operation in this Switch Series. |
J9988A, J9989A, J9990A, J9993A | KB.15.17 | J8177C/J8177D support both 100Mbps and 1G operation in this Switch Series. | |
6120 Blade Switch Series | 498358-B21, 516733-B21 | All | |
6200yl-24G-mGBIC Switch | J8992A | All | |
Aruba 6200 Switch Series | All models
Only 1G speed supported See Comments |
10.04.1000 | 100Mbps speed is NOT supported for the J8177D when used in SFP+ on the 6200 Series.
Only the following 4x4 part numbers are supported: J8177C/J8177D:
|
Aruba 6300 Switch Series | All models
Only 1G speed supported See Comments |
10.04.0001 | 100Mbps speed is NOT supported for the J8177D when used in any port (SFP+ or SFP56) on the 6300 Series.
Only the following 4x4 part numbers are supported: J8177C/J8177D:
|
Aruba 6400 Switch Series | R0X39B, R0X40B
R0X41A, R0X42A, R0X43A |
10.04.1000 | R0X39A/R0X40A (revision A) are no longer supported for use in the 6400 series
100Mbps operation is NOT supported using J8177D in this series. Only the following 4x4 part numbers are supported: J8177C/J8177D:
|
R0X44A | 10.04.2000 | ||
8100fl Switch Series | J8735A | CY.01.02.0050 | |
8200zl Switch Series | J8705A, J8706A | All | |
J9308A | K.14.34 | ||
J9537A, J9549A, J9535A, J9637A | K.15.02.0004 | ||
Aruba 8320 48p 10G SFP/SFP+ and 6p 40G QSFP+ Switch | JL479A | All | J8177D can only operate at 1G in the 8320 series.
Only the following 4x4 part numbers are supported: J8177C/J8177D:
|
Aruba 8325 Switch Series | JL624A/JL625A | 10.03.0030 | 100Mbps operation is NOT supported in this series.
Only the following 4x4 part numbers are supported: J8177C/J8177D:
RJ45 transceivers are only supported for use in the top 2 rows of ports (max of 24 per switch). J8177C/J8177D will have a delay (~15 secs) before link up or down is properly displayed when a cable is inserted or removed. The 8325 requires configuration of "interface groups" (groups of 12 ports) to enable the use of 1G or 10G transceivers / DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the Installation Guide for details. |
Aruba 8400X Modules | JL363A
JL687A |
10.00.0018
10.04.2000 |
Only the following 4x4 part numbers are supported:
Only the following 4x4 part numbers are supported: J8177C/J8177D:
JL687A notes: The 25G module (JL687A) requires configuration of "interface groups" (groups of 4 ports) to enable use of 1G or 10G transceivers or DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the Installation Guide for details. The link state of ports on the JL687A module will always show UP if a transceiver is inserted and the interface is enabled, even if the cable is disconnected |