Management module LED behavior
Management module health LED
LED state |
Meaning |
---|---|
Off |
Shut down or ready for removal |
On Green |
Booting the ArubaOS-CX operating system, ready, or normal operation |
Slow Flash Green |
Booting the BIOS or service operating system, or updating firmware |
Slow Flash Orange |
Management module fault |
Fast Flash Orange |
Software (NOS) mismatch |
Chassis temperature status (Temp) LED
LED state |
Meaning |
---|---|
On Green |
Temperature at or below rating |
Slow Flash Orange |
Environment air temperature or individual component temperature above rating |
Management state LEDs
Standby management modules do not show component status LEDs.
LED State |
Active state (Actv) |
Standby state (Stby) |
---|---|---|
On Green (only one on at a time) |
This module is the active management module and it is ready. |
This module is the standby management module and it is ready. |
Both LEDs Off |
This management module is not ready (booting or shut down). |
LED state |
Meaning |
---|---|
Off |
Operating system has not started booting Management module is ready |
Slow Flash Green |
ArubaOS-CX operating system is booting |
Status Front LEDs
LED state |
Meaning |
---|---|
Off |
Not present |
On Green |
Operating normally |
Slow Flash Orange |
Fault condition |
LED state | Meaning |
---|---|
Off |
Powered down, ready for removal |
On Green |
Ready or normal operation |
Slow Flash Green |
Booting or initializing |
Slow Flash Orange |
Fault condition |
Fast Flash Orange |
Hardware (ASIC) mismatch |
LED state |
Meaning |
---|---|
Off |
Not present or module is shut down and ready for removal |
On Green |
Operating normally |
Status Rear LEDs
LED state |
Meaning |
---|---|
Off |
Powered down, ready for removal |
On Green |
Normal operation |
Slow Flash Green |
Booting or initializing |
Slow Flash Orange |
Fault condition |
Fast Flash Orange |
Hardware (ASIC) mismatch |
LED state |
Meaning |
---|---|
On Green |
Operating normally |
Slow Flash Orange |
Fault condition or not present |
LED state |
Meaning |
---|---|
On Green |
Operating normally |
Slow Flash Orange |
One or more fans in the given fan tray is in a fault condition or is not present |
LED Mode
The LED Mode button changes the behavior of port LEDs from the default mode to cycle through various other settings. The selected LED mode reverts to the default mode after 10 minutes. The LED modes are the following:
- Default mode
In the default mode:
All LEDs in the LED Mode section are off.
Port LED behavior indicates link and activity without rate indications.
If a line module port is in a fault condition, its LED changes from Flashing Green (indicating activity) to Slow Flash Orange (fault condition).
- Speed mode
In the speed mode:
The Spd (Speed) LED is On Green.
Port LED behavior indicates link speed. A Port LED is On Green when the link is at maximum speed and Flashing Green when the link is below maximum speed.
- User 1 Mode
The behavior for the Usr1 (User 1) mode is to Light Faults. Use this mode to assist users who cannot discern between Green and Orange LEDs or who want to locate an occurring fault quickly.
In Light Faults mode:
The Usr1 (User 1) LED is On Green.
All other Green LEDs except the chassis power LEDs are Off.
LEDs that indicate a fault condition are Slow Flash Orange or Fast Flash Orange.
Auxiliary Port LED
Off (Not used).
Management Port LEDs
LED state |
Meaning |
---|---|
Off |
Port is disabled, not connected or not receiving a link indication from the connected device |
Half-Bright Green |
Port is enabled and receiving a link indication from the connected device |
Switching between Half-Bright and Full-Bright Green |
Port is actively transferring data |
On Green |
Port is at high utilization |