Validation rules
Validation |
Error/Warning/Prompt |
|---|---|
Enabling SLA without configuring SLA type. |
Cannot enable IP SLA, no valid source/destination configured. |
IP address given for source or destination is multicast or broadcast. |
Invalid IP address. |
Configure the SLA type with a source IP which is configured in the same switch. |
Destination IP cannot be configured as the same as one of the local interface IP addresses. |
Configure threshold with invalid value. |
Invalid threshold count value. For threshold type 'Immediate', count must be 1 and for 'Consecutive', count must be greater than or equals to 2. |
Configure threshold value for 'PacketLoss' or 'TestCompletion' |
Configuration is not applicable when threshold is configured for 'PacketLoss' or 'TestCompletion'. |
Configure threshold type for TestCompletion. |
Configuration is not applicable when threshold is configured for 'TestCompletion'. |
Configure schedule with proper end time with a frequency which is out of end time. |
Invalid endtime. Endtime is not enough to run the tests for configured frequency and repetitions. |
Configuring ‘srcTodstTime’ or ‘dstTosrcTime’ threshold configuration for ‘icmp-echo’ or ‘tcp-connect’. |
Invalid threshold configuration for configured SLA type. |
Enabling the IP SLA which is already in enabled state. |
IP SLA is already enabled. |
Disabling the IP SLA which is already in disabled state. |
IP SLA is already disabled. |
Show IP SLA history of un-configured SLA. |
IP SLA is not configured for this ID. |
Enable more number (currently decided 50 as limit) of IP SLA. |
Maximum number of enabled IP SLAs at a time is limited to 50. |
Removing IP SLA type/tos/history size/schedule/ threshold configuration with un-configured value. |
IP SLA configuration does not exist. |
Configuring scheduler with a frequency value which is not satisfying the condition frequency > number of packets per probe * packet interval. |
Frequency value is insufficient to configure the scheduler. |
Scheduler already configured and try to configure SLA type with a value of ‘number of packets per probe’ and ‘packet interval’ which is not satisfying the condition frequency > number of packets per probe * packet interval. |
Number of packets/packet interval is insufficient to configure IP SLA type. |
Configuring IP SLA with invalid values. |
Invalid configuration for IP SLA. |
Change the IP SLA configuration when the SLA is enabled. |
Configuration changes not allowed when IP SLA is enabled. |
When IP address vs port number configured for an SLA is already in use |
Error: Socket for configured address, port is already in use, choose different port number |
When Source IP address given in SLA configuration is not configured in the switch |
Error: Source IP address is not configured in switch |
Invalid SLA ID given in show command |
Error: Invalid IP SLA ID |
Configure SLA more than allowed limit |
Warning: The maximum number of IP SLAs allowed is 50. |
Configure Responder more than allowed limit |
Error: IP SLA Responder configurations reached max limit. No more configurations accepted. |
Configure inter-packet interval when number of packets to be sent out is one. |
Error Not applicable as Number of packets to be sent out is 1. |
Upper threshold value is less than lower threshold value. |
Error: Upper threshold value X is less than lower threshold value Y. |
Configure schedule with start time greater than stop time. |
Error: Stop time must be greater than start time. |
Configure schedule with past stop time. |
Error: Stop time must be greater than current time. |
Configure schedule with invalid frequency value. |
Error: Schedule frequency is out of range. Valid range is 5 to 604800. |
Configuring history size with invalid value. |
Error: IP SLA History size is out of range. Valid range is 1–50. |
Configuring SLA type with invalid payload value. |
IP SLA Payload value is out of range. Valid range is 1–1440. |
Configuring SLA type with invalid port number. |
Invalid port number. Valid range is 1024 to 65535. |
Configure the IPSLA parameters without configuring SLA type. |
No valid IP SLA type configuration found. |
Configuring the responder with existing details. |
IP SLA Responder with same configuration exist. |
Configure management VLAN as source VLAN. |
Error: Not allowed to configure management VLAN as source interface. |
Enabling IP SLA without required configuration parameters. |
Configuration is incomplete to enable the entry. |
Configure IPSLA UDP Jitter/VoIP session when an OpenFlow custom match mode instance is already enabled. |
Cannot enable IP SLA: Initiator cannot co-exist with OpenFlow custom Cannot enable IP SLA: Initiator cannot co-exist with OpenFlow custom |
Configure UDP Jitter/VoIP IPSLA Initiator session with a source IP same as tunnel overlay VLAN |
Cannot enable IP SLA: The source VLAN cannot be a tunnel overlay VLAN. |
Configure UDP Jitter/VoIP IPSLA Initiator session with a source IP same as a service tunnel endpoint. |
Cannot enable IP SLA: The source VLAN cannot be a service tunnel endpoint. |