Configuring STP loop guard

Spanning tree is used to ensure a loop-free topology over the LAN. Occasionally a hardware or software failure can cause STP to fail, creating STP/ forwarding loops that can cause network failures where unidirectional links are used. The non-designated port transitions in a faulty manner because the port is no longer receiving STP BPDUs.

STP Loop Guard causes the non-designated port to go into the STP loop inconsistent state instead of the forwarding state. In the loop-inconsistent state, the port prevents data traffic through the link, therefore avoiding the loop creation. When BPDUs again are received on the inconsistent port, it resumes normal STP operation automatically.

Syntax:


spanning-tree <port-list> loop-guard

no spanning-tree <port-list> loop-guard

Enables STP Loop Guard on a particular port or ports. STP Loop Guard is best applied on blocking or forwarding ports.

The no form of the command disables STP Loop Guard.

Default: Disabled

Loop creation with transmission failure

Before configuring loop guard

Before configuring Loop Guard on port 20, the status of VLAN 20 appears as follows:
switch(config)# show spanning-tree vlan 20

 Spanning Tree Information

  STP Enabled              [No] : Yes
  Mode                          : RPVST
  Extended System ID            : Enabled

  Ignore PVID Inconsistency     : Disabled
  Switch MAC Address            : 002347-c651c0


  VLAN ID                       : 20
  RPVST Enabled                 : Enabled


  Root MAC Address              : 0024a8-d13a40
  Root Priority                 : 32,768
  Root Path Cost                : 20,000
  Root Port                     : 1
  Operational Hello Time (secs) : 2
  Topology Change Count         : 2
  Time Since Last Change        : 9 secs

                                                          Designated
  Port  Type       Cost   Priority  Role       State      Bridge
  ----- ---------- ------ --------- ---------- ---------- ---------------
   1     100/1000T  20000  128       Root       Forwarding 0024a8-d13a40
   20    10/100TX   200000 128       Alternate  Blocking   002347-587b80

After configuring loop guard

This example shows that, by executing spanning-tree 20 loop-guard, loop guard has been configured on port 20 of Switch 2:
switch(config)# show spanning-tree

 Spanning Tree Information

  STP Enabled          [No] : Yes
  Mode                      : RPVST
  Extended System ID        : Enabled
  Ignore PVID Inconsistency : Disabled
  RPVST Enabled VLANs       : 20


  Switch MAC Address        : 002347-c651c0
  Root Guard Ports          :
  Loop Guard Ports          : 20
  TCN Guard Ports           :
  BPDU Protected Ports      :
  BPDU Filtered Ports       :
  Auto Edge Ports           : 1-24
  Admin Edge Ports          :

  VLAN  Root Mac        Root       Root       Root                 Hello
  ID    Address         Priority   Path-Cost  Port                 Time(sec)
  ----- --------------- ---------- ---------- -------------------- ---------
  100   0024a8-d13a40   32,768     20,000     1                    2

Switch ceasing to send BPDUs

With switch 1 ceasing to send BPDUs through port 20 to switch 2, port 20 goes into the “inconsistent” state and ceases to forward traffic, as displayed in the following show spanning-tree output for VLAN 20.

switch(config)# show spanning-tree vlan 20

 Spanning Tree Information

  STP Enabled              [No] : Yes
  Mode                          : RPVST
  Extended System ID            : Enabled
  Ignore PVID Inconsistency     : Disabled
  Switch MAC Address            : 002347-c651c0


  VLAN ID                       : 20
  RPVST Enabled                 : Enabled


  Root MAC Address              : 0024a8-d13a40
  Root Priority                 : 32,768
  Root Path Cost                : 20,000
  Root Port                     : 1
  Operational Hello Time (secs) : 2
  Topology Change Count         : 3
  Time Since Last Change        : 42 hours

                                                          Designated
  Port  Type       Cost   Priority  Role       State      Bridge
  ----- ---------- ------ --------- ---------- ---------- ---------------
  1     100/1000T  20000  128       Root       Forwarding 0024a8-d13a40
  20    10/100TX   200000 128       Alternate  Inconsi... 002347-587b80  

Displaying config file with loop guard enabled

The following example displays show spanning-tree config output with loop guard enabled on Port 20:

switch(config)# show spanning-tree config

 Spanning Tree Information

  STP Enabled          [No] : Yes
  Mode                      : RPVST
  Extended System ID        : Enabled
  Ignore PVID Inconsistency : Disabled
  RPVST Enabled VLANs       : 100


  Switch MAC Address        : 002347-c651c0

  Root Guard Ports          :
  Loop Guard Ports          : 20
  TCN Guard Ports           :
  BPDU Protected Ports      :
  BPDU Filtered Ports       :
  Auto Edge Ports           : 1-24
  Admin Edge Ports          :

                Max Age Forward    Hello     Admin Root
  VLAN Priority (sec)   Delay(sec) Time(sec) Bridge
  ---- -------- ------- ---------- --------- ----------------
  100  32768    20      15         2         Not Configured