드라이버 및 소프트웨어

• Added support for the following IO devices:
  • HPE Synergy 4820C 10/20/25Gb Converged Network Adapter
  • HPE StorFabric CN1200R-T Converged Network Adapter
  • HPE StorFabric CN1300R Converged Network Adapter
  • HPE Synergy 6410C 25/50Gb Ethernet Adapter
  • HPE Ethernet 100Gb 1-port 842QSFP28 Adapter
  • HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter
• Added the following enhancements to Control Panel Applet:
  • Up to 8 trap destinations are supported in SNMP tab, along with user configuration and SNMPv3 settings
  • SNMP tab is now fully functional if iLO5 encryption is set to HighSecurity or FIPS mode
  • Button options are available to start, stop, enable or disable SMA service
  • GUI options are available to select time format and input the optional periodic test trap interval
  • Help content has expanded
• SMA (System Management Assistant) service now supports all MIB OIDs and traps generated by iLO5 FW.
• Added support for System Chassis Class of IML Events in Windows Event Log.
• iSCSI MIB condition is now available in cpqHoMibHealthStatusArray.
• AHS (Active Health System) NIC Link records now contain Interface Description string.

Prerequisites:

The Channel Interface Driver for Windows X64 must be installed prior to this component.

Microsoft SNMP Service must be enabled, if SMA (System Management Assistant) is enabled.

To ensure the integrity of your download, HPE recommends verifying your results with the following SHA-256 Checksum values:

Reboot Requirement:
Reboot may be required after installation for updates to take effect and hardware stability to be maintained.

Installation:

Place the Smart Component in a temporary directory, then double-click it to run.

Select "Install" to start extracting to a temporary location on the hard drive.

Click the "Install" button to perform the service installation.

End User License Agreements:
HPE Software License Agreement v1
Hewlett-Packard End User License Agreement

Upgrade Requirement:
Optional - Users should update to this version if their system is affected by one of the documented fixes or if there is a desire to utilize any of the enhanced functionality provided by this version.

Important:

About installation and enablement of SMA service:

• During AMS installation in interactive mode, there is pop up message to selectively install SMA.
  • If Yes is selected, SMA service will be installed and set to running state.
  • If No is selected, SMA service will be installed but the service is not enabled.

• During AMS installation in silent mode, SMA is installed but the service is not enabled.
• To enable SMA service at a later time, go to the following folder: %ProgramFiles%\OEM\AMS\Service\ (Typically c:\Program Files\OEM\AMS\Service) and execute "EnableSma.bat /f"
• IMPORTANT: The SNMP service community name and permission must be also be setup. This is not done by “EnableSma.bat”.
• To disable SMA after it has been enabled, go the the following folder: %ProgramFiles%\OEM\AMS\Service\ (Typically c:\Program Files\OEM\AMS\Service) and execute "DisableSma.bat /f"
• After installing Windows operating system, make sure all the latest Microsoft Updates are downloaded and installed (wuapp.exe can be launched to start the update process). If this is not done, a critical error may be reported in Windows Event Log, “The Agentless Management Service terminated unexpectedly.”.

AMS Control Panel Applet:

• The AMS control panel applet UI is best displayed on the system when screen resolution is 1280 x 1024 pixels or higher and text size 100%.

Notes:

• IML events marked as repaired in ILO will not be mirrored in Windows Event Log.
• If Windows Server 2016 Device Guard policy is enabled, AMS can be upgraded from an older version to a newer version,  but it cannot be uninstalled.  To uninstall AMS, the Device Guard policy needs to be temporarily disabled.
• AMS Control Panel applet “SNMP” tab does not show SNMP settings and does not allow test trap generation
    when iLO5 encryption is set to SuiteB NSA mode.  Please use iLO5->Management page as an alternate option.

Upgrade Requirement:
Optional - Users should update to this version if their system is affected by one of the documented fixes or if there is a desire to utilize any of the enhanced functionality provided by this version.

• AMS service no longer terminates unexpectedly if the server had more than 9 IPV6 addresses.  However, cpqNicIfLogMapIPV6Address OID will only return up to 9 IPV6 addresses.   
• Traps 1015, 1019,1020 now have correct varbind info, consistent with MIB definitions.
• When SMA (System Management Assistant) service is stopped or disabled, SMA will no longer respond to SNMP queries with outdated data.

About installation and enablement of SMA service:

• During AMS installation in interactive mode, there is pop up message to selectively install SMA.
  • If Yes is selected, SMA service will be installed and set to running state.
  • If No is selected, SMA service will be installed but the service is not enabled.

• During AMS installation in silent mode, SMA is installed but the service is not enabled.
• To enable SMA service at a later time, go to the following folder: %ProgramFiles%\OEM\AMS\Service\ (Typically c:\Program Files\OEM\AMS\Service) and execute "EnableSma.bat /f"
• IMPORTANT: The SNMP service community name and permission must be also be setup. This is not done by “EnableSma.bat”.
• To disable SMA after it has been enabled, go the the following folder: %ProgramFiles%\OEM\AMS\Service\ (Typically c:\Program Files\OEM\AMS\Service) and execute "DisableSma.bat /f"
• After installing Windows operating system, make sure all the latest Microsoft Updates are downloaded and installed (wuapp.exe can be launched to start the update process). If this is not done, a critical error may be reported in Windows Event Log, “The Agentless Management Service terminated unexpectedly.”.

AMS Control Panel Applet:

• The AMS control panel applet UI is best displayed on the system when screen resolution is 1280 x 1024 pixels or higher and text size 100%.