Printable version

Drivers & software

* RECOMMENDED * Firmware Flash Component for Windows - HP MSA 1040/2040 and P2000 G3 1.2TB 6G SAS 10K rpm SFF Drive Model (EG1200FDNJT)

By downloading, you agree to the terms and conditions of the Hewlett Packard Enterprise Software License Agreement.
Note:  Some software requires a valid warranty, current Hewlett Packard Enterprise support contract, or a license fee.

Type: Firmware - SAS Storage Disk
Version: HPD8 (A)(15 Aug 2016)
Operating System(s): HP-UX 11.23
HP-UX 11.31 (IA)
Microsoft Windows Server 2008 R2
Microsoft Windows Server 2008 W32
Microsoft Windows Server 2008 x64
Microsoft Windows Server 2012
Microsoft Windows Server 2012 R2
Red Hat Enterprise Linux 5 Server (x86)
Red Hat Enterprise Linux 5 Server (x86-64)
Red Hat Enterprise Linux 6 Server (x86)
Red Hat Enterprise Linux 6 Server (x86-64)
Red Hat Enterprise Linux 7 Server
SUSE Linux Enterprise Server 11 (AMD64/EM64T)
SUSE Linux Enterprise Server 11 (x86)
SUSE Linux Enterprise Server 12
VMware ESXi 5.0
VMware vSphere 5.1
VMware vSphere 5.5
VMware vSphere 6.0
File name: cp029628.exe (4.2 MB)
This Windows Smart Component contains a firmware update for SFF hard drive model EG1200FDNJT(1.2TB 6G SAS 10K) in HP MSA 1040/2040 and P2000 G3 Storage Arrays.

Prerequisites:

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

IMPORTANT: Ensure that no other user is performing administrative functions on the HP MSA 1040/2040 and P2000 G3 Storage Arrays.

NOTE: Disk drive upgrades on the HP MSA 1040/2040 and P2000 G3 is an offline process. All host and array I/O must be stopped prior to the upgrade. For more information, see the HP Modular Storage Array Reference Guides. All firmware flash progress messages are logged to %systemdrive%\CPQSYSTEM\Log\MSA2000_IP.log and flash summary is logged to %systemdrive%\CPQSYSTEM\Log\cpqsetup.log.

IMPORTANT: Please refer to the best practices document for special considerations regarding the pre-install conditions for flashing hard drives in HP MSA 1040/2040 and P2000 G3 Storage Arrays.

IMPORTANT: HTTPS/Telnet service must be enabled on the arrays being updated and the corresponding client interfaces enabled on the host system where the smart component is being executed. The Smart Component will manage the FTP enable / disable settings in array.


To ensure the integrity of your download, HPE recommends verifying your results with this MD5 Checksum value:

b33651b514419747ee8ea8eaedb8daf9 cp029628.exe

Reboot Requirement:
Reboot is not required after installation for updates to take effect and hardware stability to be maintained.


Installation:

Installation instructions using Smart Component:

The Smart Component package is a self-extracting executable. You can execute this module from the Windows graphical user interface (GUI) or the command line console (CLI).

GUI option:

  1. Place the downloaded firmware package in a temporary directory.
  2. Using Windows Explorer, navigate to the directory containing the download.
  3. Double click the executable file.
  4. Follow onscreen instructions. After you are prompted for logon information, enter credentials for an account with management access rights.
  5. Wait for the installation to complete. During installation, each updated module automatically restarts. Upon completion, a confirmation message is displayed.

CLI option:

  1. Place the downloaded firmware package in a temporary directory.
  2. In single-domain environments, stop all I/O to array before starting the firmware update.
  3. Using Windows command prompt, navigate to the directory containing the download.
  4. Execute the Smart Component by entering the following command:        

    CPxxxxxxx.exe /target <ip_address> /user <username> /passwd <password> /s
    where:
  •  ip_address is the management IP address of the array controller
  •  username is the username account with management rights
  •  password is the password for username

Instead of command line parameters you can use the following DOS environment variables:

  •  oa_address: set this variable for the IP address of array controller
  •  oa_username : set this variable for the username of array controller
  •  oa_password : set this variable for the password of that username.

Wait for the installation to complete. During installation, each updated module automatically restarts. Upon completion, a confirmation message is displayed.

NOTE:

  • When prompted for logon information, enter credentials for an account with management access rights.
  • For details on supported command options, see the online help by executing the command CPxxxxxx.exe /h or /?.

End User License Agreements:
HPE Software License Agreement v1
Hewlett-Packard End User License Agreement


Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.

Firmware upgrade to HPD8(A) is not necessary, if the device is currently running HPD8 firmware


Important:

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

IMPORTANT: Ensure that no other user is performing administrative functions on the HP MSA 1040/2040 and P2000 G3 Storage Arrays.

NOTE: Disk drive upgrades on the HP MSA 1040/2040 and P2000 G3 is an offline process. All host and array I/O must be stopped prior to the upgrade. For more information, see the HP Modular Storage Array Reference Guides. All firmware flash progress messages are logged to %systemdrive%\CPQSYSTEM\Log\MSA2000_IP.log and flash summary is logged to %systemdrive%\CPQSYSTEM\Log\cpqsetup.log.

IMPORTANT: Please refer to the best practices document for special considerations regarding the pre-install conditions for flashing hard drives in HP MSA 1040/2040 and P2000 G3 Storage Arrays.

IMPORTANT: HTTPS/Telnet service must be enabled on the arrays being updated and the corresponding client interfaces enabled on the host system where the smart component is being executed. The Smart Component will manage the FTP enable / disable settings in array.


Supported Devices and Features:

Firmware on the listed drives can be updated when attached to any of the following Storage Systems:

  • HP MSA 2040 SAN SFF Storage
  • HP MSA 2040 SAS SFF Storage
  • HP MSA 1040 SAN SFF Storage
  • HP MSA 1040 SAS SFF Storage
  • HP P2000 G3 10GbE iSCSI MSA Dual Controller SFF Array System
  • HP P2000 G3 iSCSI MSA Dual Controller SFF Array System
  • HP P2000 G3 SAS MSA Dual Controller SFF Array System
  • HP P2000 G3 MSA FC Dual Controller SFF Modular Smart Array System
  • HP P2000 G3 MSA FC/iSCSI Dual Combo Controller SFF Array

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.

Firmware upgrade to HPD8(A) is not necessary, if the device is currently running HPD8 firmware


Following issue is fixed in this firmware version HPD8(A):

  • Fixed Japanese translation issue for drive model EG1200FDNJT in smart component.

Following issues are fixed in this firmware version HPD8:

  • Fixed background seek algorithm to allow self-test to run in the background.
  • Fixed problem with SMART temp warning on a full cache hit read workload.
  • Enabled just in time seek (JIT) in low queue depth mixed sequential and random read workloads. JIT is a power saving feature. Seek acceleration is reduced, so the head arrives just in time for the target block. Customer will see reduced power draw in this workload.
  • Fixed rare servo bug. Change servo processor to reset pending request for external memory accesses. Servo processor reset did not stop a pending external memory access request and could cause an error for an external memory access timeout. Use system-level reset of servo processor block that covers the external memory access timeout instead of internal servo processor soft reset.

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

IMPORTANT: Ensure that no other user is performing administrative functions on the HP MSA 1040/2040 and P2000 G3 Storage Arrays.

NOTE: Disk drive upgrades on the HP MSA 1040/2040 and P2000 G3 is an offline process. All host and array I/O must be stopped prior to the upgrade. For more information, see the HP Modular Storage Array Reference Guides. All firmware flash progress messages are logged to %systemdrive%\CPQSYSTEM\Log\MSA2000_IP.log and flash summary is logged to %systemdrive%\CPQSYSTEM\Log\cpqsetup.log.

IMPORTANT: Please refer to the best practices document for special considerations regarding the pre-install conditions for flashing hard drives in HP MSA 1040/2040 and P2000 G3 Storage Arrays.

IMPORTANT: HTTPS/Telnet service must be enabled on the arrays being updated and the corresponding client interfaces enabled on the host system where the smart component is being executed. The Smart Component will manage the FTP enable / disable settings in array.

Version:HPD8 (A) (15 Aug 2016)
Fixes

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.

Firmware upgrade to HPD8(A) is not necessary, if the device is currently running HPD8 firmware


Following issue is fixed in this firmware version HPD8(A):

  • Fixed Japanese translation issue for drive model EG1200FDNJT in smart component.

Following issues are fixed in this firmware version HPD8:

  • Fixed background seek algorithm to allow self-test to run in the background.
  • Fixed problem with SMART temp warning on a full cache hit read workload.
  • Enabled just in time seek (JIT) in low queue depth mixed sequential and random read workloads. JIT is a power saving feature. Seek acceleration is reduced, so the head arrives just in time for the target block. Customer will see reduced power draw in this workload.
  • Fixed rare servo bug. Change servo processor to reset pending request for external memory accesses. Servo processor reset did not stop a pending external memory access request and could cause an error for an external memory access timeout. Use system-level reset of servo processor block that covers the external memory access timeout instead of internal servo processor soft reset.

Version:HPD8 (2 Dec 2015)
Fixes

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.


Following issues are fixed in this firmware:

  • Fixed background seek algorithm to allow self-test to run in the background.
  • Fixed problem with SMART temp warning on a full cache hit read workload.
  • Enabled just in time seek (JIT) in low queue depth mixed sequential and random read workloads. JIT is a power saving feature. Seek acceleration is reduced, so the head arrives just in time for the target block. Customer will see reduced power draw in this workload.
  • Fixed rare servo bug. Change servo processor to reset pending request for external memory accesses. Servo processor reset did not stop a pending external memory access request and could cause an error for an external memory access timeout. Use system-level reset of servo processor block that covers the external memory access timeout instead of internal servo processor soft reset.

Type: Firmware - SAS Storage Disk
Version: HPD8 (A)(15 Aug 2016)
Operating System(s):
HP-UX 11.23
HP-UX 11.31 (IA)
Microsoft Windows Server 2008 R2
Microsoft Windows Server 2008 W32
Microsoft Windows Server 2008 x64
Microsoft Windows Server 2012
Microsoft Windows Server 2012 R2
Red Hat Enterprise Linux 5 Server (x86)
Red Hat Enterprise Linux 5 Server (x86-64)
Red Hat Enterprise Linux 6 Server (x86)
Red Hat Enterprise Linux 6 Server (x86-64)
Red Hat Enterprise Linux 7 Server
SUSE Linux Enterprise Server 11 (AMD64/EM64T)
SUSE Linux Enterprise Server 11 (x86)
SUSE Linux Enterprise Server 12
VMware ESXi 5.0
VMware vSphere 5.1
VMware vSphere 5.5
VMware vSphere 6.0

Description

This Windows Smart Component contains a firmware update for SFF hard drive model EG1200FDNJT(1.2TB 6G SAS 10K) in HP MSA 1040/2040 and P2000 G3 Storage Arrays.

Installation Instructions

Prerequisites:

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

IMPORTANT: Ensure that no other user is performing administrative functions on the HP MSA 1040/2040 and P2000 G3 Storage Arrays.

NOTE: Disk drive upgrades on the HP MSA 1040/2040 and P2000 G3 is an offline process. All host and array I/O must be stopped prior to the upgrade. For more information, see the HP Modular Storage Array Reference Guides. All firmware flash progress messages are logged to %systemdrive%\CPQSYSTEM\Log\MSA2000_IP.log and flash summary is logged to %systemdrive%\CPQSYSTEM\Log\cpqsetup.log.

IMPORTANT: Please refer to the best practices document for special considerations regarding the pre-install conditions for flashing hard drives in HP MSA 1040/2040 and P2000 G3 Storage Arrays.

IMPORTANT: HTTPS/Telnet service must be enabled on the arrays being updated and the corresponding client interfaces enabled on the host system where the smart component is being executed. The Smart Component will manage the FTP enable / disable settings in array.


To ensure the integrity of your download, HPE recommends verifying your results with this MD5 Checksum value:

b33651b514419747ee8ea8eaedb8daf9 cp029628.exe

Reboot Requirement:
Reboot is not required after installation for updates to take effect and hardware stability to be maintained.


Installation:

Installation instructions using Smart Component:

The Smart Component package is a self-extracting executable. You can execute this module from the Windows graphical user interface (GUI) or the command line console (CLI).

GUI option:

  1. Place the downloaded firmware package in a temporary directory.
  2. Using Windows Explorer, navigate to the directory containing the download.
  3. Double click the executable file.
  4. Follow onscreen instructions. After you are prompted for logon information, enter credentials for an account with management access rights.
  5. Wait for the installation to complete. During installation, each updated module automatically restarts. Upon completion, a confirmation message is displayed.

CLI option:

  1. Place the downloaded firmware package in a temporary directory.
  2. In single-domain environments, stop all I/O to array before starting the firmware update.
  3. Using Windows command prompt, navigate to the directory containing the download.
  4. Execute the Smart Component by entering the following command:        

    CPxxxxxxx.exe /target <ip_address> /user <username> /passwd <password> /s
    where:
  •  ip_address is the management IP address of the array controller
  •  username is the username account with management rights
  •  password is the password for username

Instead of command line parameters you can use the following DOS environment variables:

  •  oa_address: set this variable for the IP address of array controller
  •  oa_username : set this variable for the username of array controller
  •  oa_password : set this variable for the password of that username.

Wait for the installation to complete. During installation, each updated module automatically restarts. Upon completion, a confirmation message is displayed.

NOTE:

  • When prompted for logon information, enter credentials for an account with management access rights.
  • For details on supported command options, see the online help by executing the command CPxxxxxx.exe /h or /?.

Release Notes

End User License Agreements:
HPE Software License Agreement v1
Hewlett-Packard End User License Agreement


Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.

Firmware upgrade to HPD8(A) is not necessary, if the device is currently running HPD8 firmware


Important:

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

IMPORTANT: Ensure that no other user is performing administrative functions on the HP MSA 1040/2040 and P2000 G3 Storage Arrays.

NOTE: Disk drive upgrades on the HP MSA 1040/2040 and P2000 G3 is an offline process. All host and array I/O must be stopped prior to the upgrade. For more information, see the HP Modular Storage Array Reference Guides. All firmware flash progress messages are logged to %systemdrive%\CPQSYSTEM\Log\MSA2000_IP.log and flash summary is logged to %systemdrive%\CPQSYSTEM\Log\cpqsetup.log.

IMPORTANT: Please refer to the best practices document for special considerations regarding the pre-install conditions for flashing hard drives in HP MSA 1040/2040 and P2000 G3 Storage Arrays.

IMPORTANT: HTTPS/Telnet service must be enabled on the arrays being updated and the corresponding client interfaces enabled on the host system where the smart component is being executed. The Smart Component will manage the FTP enable / disable settings in array.


Supported Devices and Features:

Firmware on the listed drives can be updated when attached to any of the following Storage Systems:

  • HP MSA 2040 SAN SFF Storage
  • HP MSA 2040 SAS SFF Storage
  • HP MSA 1040 SAN SFF Storage
  • HP MSA 1040 SAS SFF Storage
  • HP P2000 G3 10GbE iSCSI MSA Dual Controller SFF Array System
  • HP P2000 G3 iSCSI MSA Dual Controller SFF Array System
  • HP P2000 G3 SAS MSA Dual Controller SFF Array System
  • HP P2000 G3 MSA FC Dual Controller SFF Modular Smart Array System
  • HP P2000 G3 MSA FC/iSCSI Dual Combo Controller SFF Array

Fixes

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.

Firmware upgrade to HPD8(A) is not necessary, if the device is currently running HPD8 firmware


Following issue is fixed in this firmware version HPD8(A):

  • Fixed Japanese translation issue for drive model EG1200FDNJT in smart component.

Following issues are fixed in this firmware version HPD8:

  • Fixed background seek algorithm to allow self-test to run in the background.
  • Fixed problem with SMART temp warning on a full cache hit read workload.
  • Enabled just in time seek (JIT) in low queue depth mixed sequential and random read workloads. JIT is a power saving feature. Seek acceleration is reduced, so the head arrives just in time for the target block. Customer will see reduced power draw in this workload.
  • Fixed rare servo bug. Change servo processor to reset pending request for external memory accesses. Servo processor reset did not stop a pending external memory access request and could cause an error for an external memory access timeout. Use system-level reset of servo processor block that covers the external memory access timeout instead of internal servo processor soft reset.

Important

WARNING! Do not power cycle or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

IMPORTANT: Ensure that no other user is performing administrative functions on the HP MSA 1040/2040 and P2000 G3 Storage Arrays.

NOTE: Disk drive upgrades on the HP MSA 1040/2040 and P2000 G3 is an offline process. All host and array I/O must be stopped prior to the upgrade. For more information, see the HP Modular Storage Array Reference Guides. All firmware flash progress messages are logged to %systemdrive%\CPQSYSTEM\Log\MSA2000_IP.log and flash summary is logged to %systemdrive%\CPQSYSTEM\Log\cpqsetup.log.

IMPORTANT: Please refer to the best practices document for special considerations regarding the pre-install conditions for flashing hard drives in HP MSA 1040/2040 and P2000 G3 Storage Arrays.

IMPORTANT: HTTPS/Telnet service must be enabled on the arrays being updated and the corresponding client interfaces enabled on the host system where the smart component is being executed. The Smart Component will manage the FTP enable / disable settings in array.

Revision History

Version:HPD8 (A) (15 Aug 2016)
Fixes

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.

Firmware upgrade to HPD8(A) is not necessary, if the device is currently running HPD8 firmware


Following issue is fixed in this firmware version HPD8(A):

  • Fixed Japanese translation issue for drive model EG1200FDNJT in smart component.

Following issues are fixed in this firmware version HPD8:

  • Fixed background seek algorithm to allow self-test to run in the background.
  • Fixed problem with SMART temp warning on a full cache hit read workload.
  • Enabled just in time seek (JIT) in low queue depth mixed sequential and random read workloads. JIT is a power saving feature. Seek acceleration is reduced, so the head arrives just in time for the target block. Customer will see reduced power draw in this workload.
  • Fixed rare servo bug. Change servo processor to reset pending request for external memory accesses. Servo processor reset did not stop a pending external memory access request and could cause an error for an external memory access timeout. Use system-level reset of servo processor block that covers the external memory access timeout instead of internal servo processor soft reset.

Version:HPD8 (2 Dec 2015)
Fixes

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.


Following issues are fixed in this firmware:

  • Fixed background seek algorithm to allow self-test to run in the background.
  • Fixed problem with SMART temp warning on a full cache hit read workload.
  • Enabled just in time seek (JIT) in low queue depth mixed sequential and random read workloads. JIT is a power saving feature. Seek acceleration is reduced, so the head arrives just in time for the target block. Customer will see reduced power draw in this workload.
  • Fixed rare servo bug. Change servo processor to reset pending request for external memory accesses. Servo processor reset did not stop a pending external memory access request and could cause an error for an external memory access timeout. Use system-level reset of servo processor block that covers the external memory access timeout instead of internal servo processor soft reset.

Legal Disclaimer: Products sold prior to the November 1, 2015 separation of Hewlett-Packard Company into Hewlett Packard Enterprise Company and HP Inc. may have older product names and model numbers that differ from current models.