Printable version

Drivers & software

** CRITICAL ** HP MSA 1040/2040/P2000 G3/MSA2000 G2 146GB,300GB SAS SFF (DG0146FARVU/EG0146FAWJC, DG0300FARVV/EG0300FAWJD, DG0146BAMYQ and DG0300BAMYR) Hard Drive Firmware

By downloading, you agree to the terms and conditions of the Hewlett Packard Enterprise Software License Agreement.
Note:  Some software requires a valid warranty, current Hewlett Packard Enterprise support contract, or a license fee.

Type: Firmware - SAS Storage Disk
Version: HPDG(24 Oct 2013)
Operating System(s):
HP-UX 11.23 | View all
Multi-part download
File name: HP_DG0146BAMYQ_HPDG.fla (897 KB)
File name: HP_DG0146FARVU_HPDG.fla (897 KB)
File name: HP_DG0300BAMYR_HPDG.fla (897 KB)
File name: HP_DG0300FARVV_HPDG.fla (897 KB)
File name: HP_EG0146FAWJC_HPDG.fla (897 KB)
File name: HP_EG0300FAWJD_HPDG.fla (897 KB)
This package contains a firmware update for the hard drive models DG0146FARVU (146GB 10K SAS), DG0146BAMYQ (146GB 10K SAS), EG0146FAWJC (146GB 10K SAS), DG0300FARVV(300GB 10K SAS), DG0300BAMYR (300GB 10K SAS) and EG0300FAWJD (300GB 10K SAS) when configured in HP MSA 1040/2040/P2000 G3/MSA2000 G2 storage arrays.

Prerequisites:
WARNING! Do not cycle power or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE: Drives of the same model in the storage system must have the same firmware revision.

NOTE: To install this firmware, you must download the firmware package from the HP website and save the file to your local filesystem.


To ensure the integrity of your download, HPE recommends verifying your results with the following SHA-256 Checksum values:

a2dcec59b7be4c629f3039bcfba15d56c2aa0a3e1d7c881fa5a808aa0f3c4943 HP_DG0146BAMYQ_HPDG.fla
c37ee12afb0cfcb7cf2ba35fdbd402452aa299d0500d7e703884d258044685ed HP_DG0300BAMYR_HPDG.fla
c85af25463711524298f67827130f4022dbed614a6e002077122279efb336fe9 HP_DG0146FARVU_HPDG.fla
28d1e9e5d1f458f407fb886013307703ceb399b696939b9b29b960a7f14f0c0b HP_EG0300FAWJD_HPDG.fla
eaa24cb9369e9874ee7fbbd5182d017cf8233e666aadf3ef634170d20681ced8 HP_DG0300FARVV_HPDG.fla
b17dc0aa571eed2f811147e6e07c350787397d992155b5e17b7c52ddf7775b60 HP_EG0146FAWJC_HPDG.fla

Reboot Requirement:
Reboot is not required after installation for updates to take effect and hardware stability to be maintained.


Installation:
Installation instructions using Storage Management Utility (SMU):

  1. Place the downloaded firmware binary file in a temporary directory.
  2. Stop I/O to vdisks before starting the firmware update.
  3. Log in to the SMU select Tools > Update Firmware. A table displays currently installed firmware versions.
  4. Select the drives to update. Click Browse and select the firmware file to install.
  5. Click Install Disk Firmware File. 
  6. Wait for progress messages to specify that the update is complete.
  7. In the SMU display, verify that the proper firmware version appears for each disk drive.  
Installation instructions using FTP:     

Using the SMU, prepare to use FTP:
  • Determine the network-port IP addresses of the system controllers.
  • Verify that the system FTP service is enabled.
  • Verify that the user you will log in as has permission to use the FTP interface and has manage access rights. 
Obtain address of the disks  
  • Obtain the address of each disk to be loaded in the form  (for example, 0:1 and 1:9) and obtain the firmware revision of each of these disks.
  • Determine which disks need to be updated based on the revision.
  • Note: In the WBI, the disk addresses are displayed by clicking on each enclosure in the Configuration View and then selecting the desired disk. The needed data is displayed in the fields labeled 'Enclosure ID','Slot', and'Revision'.
  • Note: In the CLI, enter 'show disks'. The required information is displayed in the columns labeled 'Location' and 'Revision'. 
Instructions for updating disk firmware using FTP  
 
  1. Stop all I/O to vdisks before starting the firmware update.
  2. Place the downloaded firmware binary file in a temporary directory.
  3. Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory containing the firmware file to load.
  4. Enter ftp . (For example: ftp 10.1.0.9)
  5. Log in via FTP with user name and password
  6. To update a specific drive, Type put filename disk:enclosure-ID:slot-number where filename is the new firmware image to load.
  7. It typically takes several minutes for the new firmware to messages will be displayed in this FTP interface during this time WARNING! Do not power cycle or restart during the firmware update as this can result in loss of capabilities for this unit. 
  8. Repeat steps 6-7 for each disk to update in each enclosure.
  9. Using SMU or CLI verify that the proper firmware version appears for each disk drive.

End User License Agreements:
Hewlett-Packard End User License Agreement


Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


Important:
CAUTION: Updating firmware on drives in a virtual disk causes the drives to be temporarily inaccessible and increases the risk of data loss

IMPORTANT: Drive upgrades are an offline process. All host and array I/O must be stopped prior to the upgrade.


Notes:

Deliverable Name:
      HP MSA 1040/2040/P2000 G3/MSA2000 G2 146GB,300GB  SAS SFF Hard Drive (DG0146FARVU, DG0300FARVV, DG0146BAMYQ, DG0300BAMYR, EG0146FAWJC, and EG0300FAWJD) Firmware

Release Version:
      HPDG

 


Supported Devices and Features:
Firmware on the listed drives can be updated when attached to any MSA 1040/2040/P2000 G3 or MSA2000 G2 array controller enclosure.


Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


  • This firmware corrects a possible condition in which stale data might be written to the disk.  This results in unexpected data being returned in subsequent requests.
CAUTION: Updating firmware on drives in a virtual disk causes the drives to be temporarily inaccessible and increases the risk of data loss

IMPORTANT: Drive upgrades are an offline process. All host and array I/O must be stopped prior to the upgrade.
Version:HPDG (24 Oct 2013)
Fixes

Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


  • This firmware corrects a possible condition in which stale data might be written to the disk.  This results in unexpected data being returned in subsequent requests.

Version:HPDC (29 Nov 2011)
Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


This firmware prevents the following:

  • Possible HDD hang when the drive is used in a dual domain or dual path fail-over environment and communication to one path is suddenly lost
  • Over-writing data written via the fail over port when data is written via a port performing interface recovery (discovery) 
  • A situation where the drive reports self test in progress erroneously after self test was interrupted by a power cycle or hot plug

Version:HPD8 (15 Sep 2011)
Enhancements

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Decreases the number of command timeouts caused by error recovery by improving drive background data checking algorithms, particularly in high usage environments.


Version:HPD6 (18 Oct 2010)
Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


  • Corrects a data transfer issue during write cache enabled operations.
  • Extends watchdog timers to resolve possible dropped data frames.

Version:HPD5 (27 Sep 2010)
Enhancements

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.

Use this firmware to flash supported drives in P2000 G3 MSA and MSA2000 G2 configurations ONLY.

Do not use this firmware to flash the drives if the drives are in any other configurations.


Initial release of specially packaged firmware for use in P2000 G3 MSA and MSA2000 G2 configurations ONLY.


Type: Firmware - SAS Storage Disk
Version: HPDG(24 Oct 2013)
Operating System(s):
HP-UX 11.23
HP-UX 11.31 (IA)
Microsoft Windows Server 2003
Microsoft Windows Server 2003 64-Bit Edition
Microsoft Windows Server 2003 for 64-bit Extended Systems
Microsoft Windows Server 2008 Itanium
Microsoft Windows Server 2008 R2
Microsoft Windows Server 2008 R2 for Itanium-Based Systems
Microsoft Windows Server 2008 W32
Microsoft Windows Server 2008 x64
Microsoft Windows Server 2012
Microsoft Windows Server 2012 R2
Red Hat Enterprise Linux 4 (AMD64/EM64T)
Red Hat Enterprise Linux 4 (Itanium)
Red Hat Enterprise Linux 4 (x86)
Red Hat Enterprise Linux 5 Server (Itanium)
Red Hat Enterprise Linux 5 Server (x86)
Red Hat Enterprise Linux 5 Server (x86-64)
Red Hat Enterprise Linux 6 Server (x86)
Red Hat Enterprise Linux 6 Server (x86-64)
Solaris 10 for x86 Systems
SUSE Linux Enterprise Server 10 (AMD64/EM64T)
SUSE Linux Enterprise Server 10 (Itanium)
SUSE Linux Enterprise Server 10 (x86)
SUSE Linux Enterprise Server 11 (AMD64/EM64T)
SUSE Linux Enterprise Server 11 (Itanium)
SUSE Linux Enterprise Server 11 (x86)
VMware ESX/ESXi 4.0
VMware ESX/ESXi 4.1
VMware ESXi 5.0
VMware vSphere 5.1
VMware vSphere 5.5

Description

This package contains a firmware update for the hard drive models DG0146FARVU (146GB 10K SAS), DG0146BAMYQ (146GB 10K SAS), EG0146FAWJC (146GB 10K SAS), DG0300FARVV(300GB 10K SAS), DG0300BAMYR (300GB 10K SAS) and EG0300FAWJD (300GB 10K SAS) when configured in HP MSA 1040/2040/P2000 G3/MSA2000 G2 storage arrays.

Installation Instructions

Prerequisites:
WARNING! Do not cycle power or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE: Drives of the same model in the storage system must have the same firmware revision.

NOTE: To install this firmware, you must download the firmware package from the HP website and save the file to your local filesystem.


To ensure the integrity of your download, HPE recommends verifying your results with the following SHA-256 Checksum values:

a2dcec59b7be4c629f3039bcfba15d56c2aa0a3e1d7c881fa5a808aa0f3c4943 HP_DG0146BAMYQ_HPDG.fla
c37ee12afb0cfcb7cf2ba35fdbd402452aa299d0500d7e703884d258044685ed HP_DG0300BAMYR_HPDG.fla
c85af25463711524298f67827130f4022dbed614a6e002077122279efb336fe9 HP_DG0146FARVU_HPDG.fla
28d1e9e5d1f458f407fb886013307703ceb399b696939b9b29b960a7f14f0c0b HP_EG0300FAWJD_HPDG.fla
eaa24cb9369e9874ee7fbbd5182d017cf8233e666aadf3ef634170d20681ced8 HP_DG0300FARVV_HPDG.fla
b17dc0aa571eed2f811147e6e07c350787397d992155b5e17b7c52ddf7775b60 HP_EG0146FAWJC_HPDG.fla

Reboot Requirement:
Reboot is not required after installation for updates to take effect and hardware stability to be maintained.


Installation:
Installation instructions using Storage Management Utility (SMU):

  1. Place the downloaded firmware binary file in a temporary directory.
  2. Stop I/O to vdisks before starting the firmware update.
  3. Log in to the SMU select Tools > Update Firmware. A table displays currently installed firmware versions.
  4. Select the drives to update. Click Browse and select the firmware file to install.
  5. Click Install Disk Firmware File. 
  6. Wait for progress messages to specify that the update is complete.
  7. In the SMU display, verify that the proper firmware version appears for each disk drive.  
Installation instructions using FTP:     

Using the SMU, prepare to use FTP:
  • Determine the network-port IP addresses of the system controllers.
  • Verify that the system FTP service is enabled.
  • Verify that the user you will log in as has permission to use the FTP interface and has manage access rights. 
Obtain address of the disks  
  • Obtain the address of each disk to be loaded in the form  (for example, 0:1 and 1:9) and obtain the firmware revision of each of these disks.
  • Determine which disks need to be updated based on the revision.
  • Note: In the WBI, the disk addresses are displayed by clicking on each enclosure in the Configuration View and then selecting the desired disk. The needed data is displayed in the fields labeled 'Enclosure ID','Slot', and'Revision'.
  • Note: In the CLI, enter 'show disks'. The required information is displayed in the columns labeled 'Location' and 'Revision'. 
Instructions for updating disk firmware using FTP  
 
  1. Stop all I/O to vdisks before starting the firmware update.
  2. Place the downloaded firmware binary file in a temporary directory.
  3. Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory containing the firmware file to load.
  4. Enter ftp . (For example: ftp 10.1.0.9)
  5. Log in via FTP with user name and password
  6. To update a specific drive, Type put filename disk:enclosure-ID:slot-number where filename is the new firmware image to load.
  7. It typically takes several minutes for the new firmware to messages will be displayed in this FTP interface during this time WARNING! Do not power cycle or restart during the firmware update as this can result in loss of capabilities for this unit. 
  8. Repeat steps 6-7 for each disk to update in each enclosure.
  9. Using SMU or CLI verify that the proper firmware version appears for each disk drive.

Release Notes

End User License Agreements:
Hewlett-Packard End User License Agreement


Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


Important:
CAUTION: Updating firmware on drives in a virtual disk causes the drives to be temporarily inaccessible and increases the risk of data loss

IMPORTANT: Drive upgrades are an offline process. All host and array I/O must be stopped prior to the upgrade.


Notes:

Deliverable Name:
      HP MSA 1040/2040/P2000 G3/MSA2000 G2 146GB,300GB  SAS SFF Hard Drive (DG0146FARVU, DG0300FARVV, DG0146BAMYQ, DG0300BAMYR, EG0146FAWJC, and EG0300FAWJD) Firmware

Release Version:
      HPDG

 


Supported Devices and Features:
Firmware on the listed drives can be updated when attached to any MSA 1040/2040/P2000 G3 or MSA2000 G2 array controller enclosure.


Fixes

Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


  • This firmware corrects a possible condition in which stale data might be written to the disk.  This results in unexpected data being returned in subsequent requests.

Important

CAUTION: Updating firmware on drives in a virtual disk causes the drives to be temporarily inaccessible and increases the risk of data loss

IMPORTANT: Drive upgrades are an offline process. All host and array I/O must be stopped prior to the upgrade.

Revision History

Version:HPDG (24 Oct 2013)
Fixes

Upgrade Requirement:
Critical - HPE requires users update to this version immediately.


  • This firmware corrects a possible condition in which stale data might be written to the disk.  This results in unexpected data being returned in subsequent requests.

Version:HPDC (29 Nov 2011)
Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


This firmware prevents the following:

  • Possible HDD hang when the drive is used in a dual domain or dual path fail-over environment and communication to one path is suddenly lost
  • Over-writing data written via the fail over port when data is written via a port performing interface recovery (discovery) 
  • A situation where the drive reports self test in progress erroneously after self test was interrupted by a power cycle or hot plug

Version:HPD8 (15 Sep 2011)
Enhancements

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Decreases the number of command timeouts caused by error recovery by improving drive background data checking algorithms, particularly in high usage environments.


Version:HPD6 (18 Oct 2010)
Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


  • Corrects a data transfer issue during write cache enabled operations.
  • Extends watchdog timers to resolve possible dropped data frames.

Version:HPD5 (27 Sep 2010)
Enhancements

Upgrade Requirement:
Recommended - HPE recommends users update to this version at their earliest convenience.

Use this firmware to flash supported drives in P2000 G3 MSA and MSA2000 G2 configurations ONLY.

Do not use this firmware to flash the drives if the drives are in any other configurations.


Initial release of specially packaged firmware for use in P2000 G3 MSA and MSA2000 G2 configurations ONLY.


Legal Disclaimer: Products sold prior to the November 1, 2015 separation of Hewlett-Packard Company into Hewlett Packard Enterprise Company and HP Inc. may have older product names and model numbers that differ from current models.