Printable version

Drivers & software

* RECOMMENDED * HP MSA 1040/2040, P2000 G3 and MSA2000 G2 300GB, 450GB, 600GB and 900GB 6G SAS 10K rpm SFF Drive Models ( EG0300FCHHR, EG0450FCHHT, EG0600FCHHU and EG0900FCHHV ) Hard Drive Firmware

By downloading, you agree to the terms and conditions of the Hewlett Packard Enterprise Software License Agreement.
Note:  Some software requires a valid warranty, current Hewlett Packard Enterprise support contract, or a license fee.

Type: Firmware - SAS Storage Disk
Version: HPD8(23 Jun 2015)
Operating System(s):
HP-UX 11.23 | View all
Multi-part download
File name: HP_EG0450FCHHT_HPD8.fla (1.8 MB)
File name: HP_EG0300FCHHR_HPD8.fla (1.8 MB)
File name: HP_EG0600FCHHU_HPD8.fla (1.8 MB)
File name: HP_EG0900FCHHV_HPD8.fla (1.8 MB)
The firmware available in this download is specifically packaged for flashing the SFF hard drive models EG0300FCHHR (300GB 10K SAS 6G), EG0450FCHHT (450GB 10K SAS 6G), EG0600FCHHU (600GB 10K SAS 6G) and EG0900FCHHV (900GB 10K SAS 6G) when configured in HP MSA 1040/2040, P2000 G3/MSA2000 G2 Storage Arrays.

◾Improved write protection robustness before drive spin down.
◾Implemented minor performance improvements in RAID environments.

Prerequisites:
WARNING! Do not cycle power or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE: Drives of the same model in the storage system must have the same firmware revision.

NOTE: To install this firmware, you must download the firmware package from the HP website and save the file to your local filesystem.


To ensure the integrity of your download, HP recommends verifying your results with the following MD5 Checksum values:

ab0e8af8cca5dd3d5369b75567fb4979 HP_EG0600FCHHU_HPD8.fla
8cf7c653311bdb314127423a66a75755 HP_EG0450FCHHT_HPD8.fla
6030c1484b4dd24f1853a71e44f8b7f6 HP_EG0300FCHHR_HPD8.fla
96c2a12f2d386261b06dcb77aa43162e HP_EG0900FCHHV_HPD8.fla

Reboot Requirement:
Reboot is not required after installation for updates to take effect and hardware stability to be maintained.


Installation:
Installation instructions using Storage Management Utility (SMU):

  1. Place the downloaded firmware binary file in a temporary directory.
  2. Stop I/O to vdisks before starting the firmware update.
  3. Log in to the SMU select Tools > Update Firmware. A table displays currently installed firmware versions.
  4. Select the drives to update. Click Browse and select the firmware file to install.
  5. Click Install Disk Firmware File. 
  6. Wait for progress messages to specify that the update is complete.
  7. In the SMU display, verify that the proper firmware version appears for each disk drive.  
Installation instructions using FTP:     

Using the SMU, prepare to use FTP:
  • Determine the network-port IP addresses of the system controllers.
  • Verify that the system FTP service is enabled.
  • Verify that the user you will log in as has permission to use the FTP interface and has manage access rights. 
Obtain address of the disks  
  • Obtain the address of each disk to be loaded in the form  (for example, 0:1 and 1:9) and obtain the firmware revision of each of these disks.
  • Determine which disks need to be updated based on the revision.
  • Note: In the WBI, the disk addresses are displayed by clicking on each enclosure in the Configuration View and then selecting the desired disk. The needed data is displayed in the fields labeled 'Enclosure ID','Slot', and'Revision'.
  • Note: In the CLI, enter 'show disks'. The required information is displayed in the columns labeled 'Location' and 'Revision'. 
Instructions for updating disk firmware using FTP  
 
  1. Stop all I/O to vdisks before starting the firmware update.
  2. Place the downloaded firmware binary file in a temporary directory.
  3. Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory containing the firmware file to load.
  4. Enter ftp . (For example: ftp 10.1.0.9)
  5. Log in via FTP with user name and password
  6. To update a specific drive, Type put filename disk:enclosure-ID:slot-number where filename is the new firmware image to load.
  7. It typically takes several minutes for the new firmware to messages will be displayed in this FTP interface during this time WARNING! Do not power cycle or restart during the firmware update as this can result in loss of capabilities for this unit. 
  8. Repeat steps 6-7 for each disk to update in each enclosure.
  9. Using SMU or CLI verify that the proper firmware version appears for each disk drive.

End User License Agreements:
Hewlett-Packard End User License Agreement


Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Important:

WARNING! Do not cycle power or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE: Drives of the same model in the storage system must have the same firmware revision.

NOTE: To install this firmware, you must download the firmware package from the HP website and save the file to your local filesystem.


Supported Devices and Features:

Firmware on the listed drives can be updated when attached to any MSA 1040/2040, P2000 G3 or MSA2000 G2 Storage Arrays.


Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Fixes a potential issue where the drive could become unresponsive if the host sent a high number of overlapping task management commands (the drive would require a power cycle to be recovered).

WARNING! Do not cycle power or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE: Drives of the same model in the storage system must have the same firmware revision.

NOTE: To install this firmware, you must download the firmware package from the HP website and save the file to your local filesystem.

Version:HPD8 (23 Jun 2015)
Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Fixes a potential issue where the drive could become unresponsive if the host sent a high number of overlapping task management commands (the drive would require a power cycle to be recovered).

Enhancements

◾Improved write protection robustness before drive spin down.
◾Implemented minor performance improvements in RAID environments.


Type: Firmware - SAS Storage Disk
Version: HPD8(23 Jun 2015)
Operating System(s):
HP-UX 11.23
HP-UX 11.31 (IA)
Microsoft Windows Server 2008 Itanium
Microsoft Windows Server 2008 R2
Microsoft Windows Server 2008 R2 for Itanium-Based Systems
Microsoft Windows Server 2008 W32
Microsoft Windows Server 2008 x64
Microsoft Windows Server 2012
Microsoft Windows Server 2012 Essentials
Microsoft Windows Server 2012 R2
Red Hat Enterprise Linux 5 Server (Itanium)
Red Hat Enterprise Linux 5 Server (x86)
Red Hat Enterprise Linux 5 Server (x86-64)
Red Hat Enterprise Linux 6 Server (x86)
Red Hat Enterprise Linux 6 Server (x86-64)
Red Hat Enterprise Linux 7 Server
SUSE Linux Enterprise Server 10 (AMD64/EM64T)
SUSE Linux Enterprise Server 10 (Itanium)
SUSE Linux Enterprise Server 10 (x86)
SUSE Linux Enterprise Server 11 (AMD64/EM64T)
SUSE Linux Enterprise Server 11 (Itanium)
SUSE Linux Enterprise Server 11 (x86)
SUSE Linux Enterprise Server 12
VMware ESXi 5.0
VMware vSphere 5.1
VMware vSphere 5.5

Description

The firmware available in this download is specifically packaged for flashing the SFF hard drive models EG0300FCHHR (300GB 10K SAS 6G), EG0450FCHHT (450GB 10K SAS 6G), EG0600FCHHU (600GB 10K SAS 6G) and EG0900FCHHV (900GB 10K SAS 6G) when configured in HP MSA 1040/2040, P2000 G3/MSA2000 G2 Storage Arrays.

Enhancements

◾Improved write protection robustness before drive spin down.
◾Implemented minor performance improvements in RAID environments.

Installation Instructions

Prerequisites:
WARNING! Do not cycle power or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE: Drives of the same model in the storage system must have the same firmware revision.

NOTE: To install this firmware, you must download the firmware package from the HP website and save the file to your local filesystem.


To ensure the integrity of your download, HP recommends verifying your results with the following MD5 Checksum values:

ab0e8af8cca5dd3d5369b75567fb4979 HP_EG0600FCHHU_HPD8.fla
8cf7c653311bdb314127423a66a75755 HP_EG0450FCHHT_HPD8.fla
6030c1484b4dd24f1853a71e44f8b7f6 HP_EG0300FCHHR_HPD8.fla
96c2a12f2d386261b06dcb77aa43162e HP_EG0900FCHHV_HPD8.fla

Reboot Requirement:
Reboot is not required after installation for updates to take effect and hardware stability to be maintained.


Installation:
Installation instructions using Storage Management Utility (SMU):

  1. Place the downloaded firmware binary file in a temporary directory.
  2. Stop I/O to vdisks before starting the firmware update.
  3. Log in to the SMU select Tools > Update Firmware. A table displays currently installed firmware versions.
  4. Select the drives to update. Click Browse and select the firmware file to install.
  5. Click Install Disk Firmware File. 
  6. Wait for progress messages to specify that the update is complete.
  7. In the SMU display, verify that the proper firmware version appears for each disk drive.  
Installation instructions using FTP:     

Using the SMU, prepare to use FTP:
  • Determine the network-port IP addresses of the system controllers.
  • Verify that the system FTP service is enabled.
  • Verify that the user you will log in as has permission to use the FTP interface and has manage access rights. 
Obtain address of the disks  
  • Obtain the address of each disk to be loaded in the form  (for example, 0:1 and 1:9) and obtain the firmware revision of each of these disks.
  • Determine which disks need to be updated based on the revision.
  • Note: In the WBI, the disk addresses are displayed by clicking on each enclosure in the Configuration View and then selecting the desired disk. The needed data is displayed in the fields labeled 'Enclosure ID','Slot', and'Revision'.
  • Note: In the CLI, enter 'show disks'. The required information is displayed in the columns labeled 'Location' and 'Revision'. 
Instructions for updating disk firmware using FTP  
 
  1. Stop all I/O to vdisks before starting the firmware update.
  2. Place the downloaded firmware binary file in a temporary directory.
  3. Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory containing the firmware file to load.
  4. Enter ftp . (For example: ftp 10.1.0.9)
  5. Log in via FTP with user name and password
  6. To update a specific drive, Type put filename disk:enclosure-ID:slot-number where filename is the new firmware image to load.
  7. It typically takes several minutes for the new firmware to messages will be displayed in this FTP interface during this time WARNING! Do not power cycle or restart during the firmware update as this can result in loss of capabilities for this unit. 
  8. Repeat steps 6-7 for each disk to update in each enclosure.
  9. Using SMU or CLI verify that the proper firmware version appears for each disk drive.

Release Notes

End User License Agreements:
Hewlett-Packard End User License Agreement


Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Important:

WARNING! Do not cycle power or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE: Drives of the same model in the storage system must have the same firmware revision.

NOTE: To install this firmware, you must download the firmware package from the HP website and save the file to your local filesystem.


Supported Devices and Features:

Firmware on the listed drives can be updated when attached to any MSA 1040/2040, P2000 G3 or MSA2000 G2 Storage Arrays.


Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Fixes a potential issue where the drive could become unresponsive if the host sent a high number of overlapping task management commands (the drive would require a power cycle to be recovered).

Important

WARNING! Do not cycle power or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming.

CAUTION: Before upgrading firmware, ensure that the storage system configuration is stable and is not being reconfigured or changed in any way. If configuration changes are in progress, monitor them and wait until they are completed before proceeding with the upgrade.

IMPORTANT: As with any firmware upgrade, it is a recommended best practice to ensure that you have a full backup prior to the upgrade.

NOTE: Drives of the same model in the storage system must have the same firmware revision.

NOTE: To install this firmware, you must download the firmware package from the HP website and save the file to your local filesystem.

Revision History

Version:HPD8 (23 Jun 2015)
Fixes

Upgrade Requirement:
Recommended - HP recommends users update to this version at their earliest convenience.


Fixes a potential issue where the drive could become unresponsive if the host sent a high number of overlapping task management commands (the drive would require a power cycle to be recovered).

Enhancements

◾Improved write protection robustness before drive spin down.
◾Implemented minor performance improvements in RAID environments.


Legal Disclaimer: Products sold prior to the November 1, 2015 separation of Hewlett-Packard Company into Hewlett Packard Enterprise Company and HP Inc. may have older product names and model numbers that differ from current models.